background image

Statement

 

Dear Customer! 

We would like to congratulate you on your new Greenhouse purchase. 
We hope that by following the detailed assembly instructions you will find as much pleasure in assembly process 
same as the time you will spend in your greenhouse in the future.

  

 
The assembly instructions mainly consist of detailed illustrations and no specific technical knowledge is required 
for the assembly of the greenhouse. 

 

Depending on the model & accessories package you purchased you may have received multiple packages. The 
main ClimaPod house (not counting in accessories or extended models) has three main master packages: 

Straight Frame & Base 

Panels 

Curved Frame 

7’ Extension Set also come in three different packages. 

 

The aluminum base, straight frame profiles, as well as supporting hardware are packed in one carton. The 
greenhouse curved frames or 

“arches” are packed in a curved shape package. 

All the polycarbonate panels are packed in one carton. 

 

All of the aluminum profiles are marked with a part number corresponding to the numbers given on the draw-
ings and listed on the parts list. Nuts, bolts, and fittings will be found in the relevant package. 

 

All of the rear gable section straight frames are in package No.1   
All of the front gable section straight frames are in package No.2  
All of the roof/side wall section straight frames are in package No.3 
All of the frames and components for the window are in package No.4  
All of the frames and components for the door are in package No.5 
Each  of  the  polycarbonate  panels  have  are  labeled  with  item  number  corresponding  to  the  instructions.  You 
may  also  differentiate  them  by  their  size  and  shape.  Note:  once  you  get  to  insert  the  polycarbonate  panels, 
make sure to have the side with opal white film facing outside.

 

  

Accessories 

Modular Organics LCC (ClimaPod) offers a wide range of accessories which contribute to a better yield and 
make life easier for the gardener. A selection of the range is shown in the supplements to these instructions. Upon 
the request, your local dealer may provide you with more information about available accessories. You may also 
refer to our main website www.ClimaPod.com

 

for more information.

 

 

 

 
Winter Protection 

In areas where snow might be expected we recommend the following in order to protect your green- house: 
1.  Support the ridge at the center of the greenhouse. 
2.  Remove larger snow loads by sliding them down the sides. 
3.  Take precautions against snow falling down. 
 

Complaints

  

We put severe demands on quality to secure that you get a faultless product. However, should a problem occur, 
we kindly ask you to contact the dealer from whom you have bought the greenhouse. For a quick service, you 
should  specify  the  extent  of  the  defect  by  means  of  the  parts  list  in  the  assembly instructions. Please 
also note to mention the model number which is marked on the front page of these instructions. 
 

Guarantee

  

We grant a 10 year comprehensive guarantee which covers replacement or repairs of defective parts due to ma-
terial  or  manufacturing  defect. The guarantee does not cover polycarbonate, transport, erection. The guarantee 
is invalid if the greenhouse is not assembled according to these instructions. 

 
Insurance  

Not all insurance companies automatically cover greenhouses. We strongly recommend you contact your insur-
ance agent to ensure that your greenhouse is added to the coverage once assembled. 

Содержание VIRTUE V9 Series








































Отзывы: