Timer op tions
The system’s built-in electronic timer can be optionally wired to provide one of several different functions. Timer duration settings can be made by your
installing Clifford Dealer or by you via the CliffNet Wizard. Ask your Authorized Clifford Dealer for further details:
Re mote con trolled timed head light activation option
The timer can be wired to provide remote controlled headlight activation for any duration you wish between 1 second and 4 minutes, allowing you to
remotely light your way to and from the vehicle by pressing the
button on your remote control.
Win dow AutoClose op tion
The timer can automatically close the windows upon remote arming on vehicles with an “all-close” feature that raises them if the key is held in the driver's
door (a common feature on several European vehicle models).
NOTE: Although this timer circuit could be wired to control power windows on non-European cars that do not have
this key-in-the-door “all-close” feature, Clifford Electronics strongly recommends against this. If so wired, the timer
would force the window motors to “shut” the windows even if they were already closed. This places excessive strain
on the vehicle’s window motors, causing overheating, premature failure and even the possibility of fire. As such, if
you cannot close the windows of your vehicle by turning and holding the key in the driver’s door, do not permit the
system’s timer circuit to be wired to automatically close the windows.
If your car does not have an all-close feature, one or more SmartWindows 4 accessories are needed. One SmartWindows 4 module can control two power
windows. In addition to automatically closing the power windows every time you arm, SmartWindows 4 also allows you to remotely roll down the
windows after disarming and to remotely vent them open slightly for ventilation on hot days. Inside the car, SmartWindows 4 also provides one-touch full
open, one-touch full close and one-touch stop to each of your factory window control switches.
Win dow AutoClose In stant By pass
If you have the timer-based window closure option noted above, you may choose to arm
without
automatically closing the windows. This is handy on hot
days by allowing you to leave one or more windows slightly open while the system remains armed. To do so, simply turn the ignition switch to “ON” and
then “OFF” rapidly. You will hear a chirp confirmation (this action also activates
Instant AutoArming bypass
prevously noted). When you then exit and
arm, the system will
not
close the windows. Normal autoclose operation is restored the next time you arm.
Turbo timer op tion
Vehicles that have turbocharged engines often require a cool-down period of one to several minutes after driving, particularly high-rev driving. Until now,
drivers of such vehicles had two choices: sit in the car after parking and wait several minutes to turn off the engine, or have an expensive turbo timer
accessory added that would often interfere with car alarm operation. But with the addition of an optional relay, your system’s timer output can save you
money and make turbo cool-down easy and convenient. If you have this option installed, just press the assigned button or button combination(your
Clifford installer will have told you which he has assigned to this function) on the remote control before shutting off the engine. Then remove your car
key (the engine will continue running), exit, and press the
button to arm the system and lock the doors. While the system is armed, your
IntelliGuard 6000 will continue to idle the engine for any duration you choose up to 4 minutes. To ensure against any possibility of false alarms, the
system will keep the sensors offline while the engine is idling, then automatically bring them back online right after the engine is shut down.
Smart Au toTest ing™
Each time you remotely arm the system, it tests all triggers and sensors. If the
hood or trunk
is open, the system will
immediately
sound
4 chirps
and
4
indicator light flashes
instead of the usual 2 and 2. If a
door
is ajar, you’ll receive 2 chirps and 2 flashes, then,
5 seconds later
, there will be
4 chirps
and
4
flashes
. If a
sensor
is malfunctioning, you will receive the usual 2 chirps and 2 flashes, then,
10 seconds later
, there will be
4 chirps
and
4 flashes
.
NOTE: Since this is a warn ing in di ca tion, you will hear the 4 chirps even if you use the chirp mut ing fea ture.
n
Specific malfunction identification:
The system can also indicate the
specific
trigger or sensor that is malfunctioning. If you get the
4-chirp/4-flash signal upon arming, perform the following to identify the malfunctioning trigger or sensor:
1. Remotely disarm, then turn on the ignition. The LED status indicator inside your vehicle will be flashing, pause, then repeat.
2. Count the number of flashes in one cycle between pauses (for your convenience, the flash cycle repeats a total of 5 times) and refer to the chart below:
LED flashes
Mean ing
1 flash
Activation of Glass Tampering Sensor
2 flashes
Activation of Piezo Sensor
4 flashes*
Door open/ajar
5 flashes
Trunk/hood open/ajar (trunk only if you have the IntelliStart 4 option)
6 flashes
Hood open/ajar (only if you have the IntelliStart 4 option)
7 flashes
Ignition switch was turned on while the system was armed
8 flashes
Three or more incorrect valet codes were entered
10 flashes
Power tampering or the vehicle battery is very low
* If your ve hi cle has a factory- installed fea ture that turns off or dims the in te rior cour tesy lights sev eral sec onds af ter you exit the ve hi cle, the sys tem can not pro vide this in di ca tion.
7
Содержание IntelliGuard 6000
Страница 1: ......
