background image

3

1.BEFORE  YOU BEGIN

What is  included

1 x Fixture
1 x Power  cable with plug
1 x User  Manua

Unpacking Instructions

Immediately  upon  receiving   a  fixture,  carefully   unpack  the  carton;   check  the 

contents  to  ensure   that  all  parts   are  present,  and   have  been  received   in  good 
condition.  Notify  the  shipper  immediately  and   retain  packing  material   for 
inspection if any  parts appear damaged  from shipping or  the carton itself  shows 
signs of mishandling.  Save the carton  and all packing  materials. In the  event that 
a fixture must  be returned to  the factory , it is  important that the fixture be returned  
in the original factory box and  packing.

AC POWER

This fixture has  an auto-switching switch-mode  power supply that  can 
accommodate a wide  range of input  voltages. The  only thing necessary  to do 
before powering on  the unit is  to make sure  the line voltage  you are applying  is 
within the range of accepted voltages.  This fixture  will accommodate between  
100V and 240V  AC 50-60  Hz. 

Help preserve the  environment! Ensure that  this product is  

recycled at the  end of its  life. Y our supplier can  give details 

of local arrangements  for the disposal  of  products.

Содержание Quadcolor Mini Par 156120





















Отзывы: