Cleveland SteamerGard WT-300 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 18

Cleveland SteamerGard WT-300 Скачать руководство пользователя страница 14

Control Panel Installation, Connection to Steamer

The control panel provides a water quality monitor (Fig. 5, Item 6), bypass valve (Fig. 5, Item 4) and storage tank pressure
gauge (Fig. 5, Item 5). The water quality monitor measures the quality of water provided by the SieamerGard. If a red light is
noted, service is required. The bypass valve allows operation of the steamer on tap water in the event of failure of the
SteamerGard system.

1. Position the control panel on a wall in the vicinity of the

steamer (See Figure 2). You will also need access to a
cold water supply.

2. Mount the control panel to the wall using the four

#10x1 1/2" screws and wall anchors provided.

3. Tap into a cold water supply line near the control panel.

We recommend the installation of a ball valve at the
point you tap into the cold water supply. Run a line
from the cold water supply to the control panel. If the
distance is 25' or less, use 3/8" O.D. polybutylene
tubing. For longer runs, use 1/2' O.D. tubing and reduce
down at the control panel. Connect this line to the
"Bypass" fitting (Fig. 5, Item 2) on the control panel.

4. Connect a 3/8" O.D. polybutylene line to the open end

of the Tee on the storage tank. Run this line from the
tank to the SteamerGard connection on the control
panel. (Fig. 5, Item 1)

5. Connect a 3/8" O.D. polybutylene line to the outlet on the control panel (Fig. 5, Item 3). Connect me other end of this

line to the steam generator (boiler) connection on the steamer. Install a check valve as directed in the steamer manual
at the inlet connection to the steam generator. The fitting and check valve required to make this connection are not
included in the SteamerGard system.

NOTE: Do not connect the purified water to the condenser. The condenser must be connected to a separate
cold water supply.

The SteamerGard installation is now complete. You can now start-up the steamer
by following the start-up instructions for the steamer.

12

«
...
12
13
14
15
16
...
»

Содержание SteamerGard WT-300



















Отзывы:

Нет отзывов