Cleveland Steel Tool 55 Ton Скачать руководство пользователя страница 26

Страница: 26 / 44

Cleveland Steel Tool Ironworkers allow for Oversize 228 Punch

and 419 Die tooling to be installed in either the punch station

or the open station. 228/419 tooling has a capacity of a 1-1/2"

round hole through 5/16" thick mild steel.

Setup

228/419 tooling includes an 228 punch stripper, 228 punch

holder assembly, 419 die table or 419 pedestal die table and

an oversized wrench. Punches and dies are wearing parts

and will need to be maintained or replaced over time. When

installing oversize punch and die tooling please observe the

following steps:

Turn off power to machine by depressing the red stop / off

button or lockout upstream power at the main electrical panel.

Install the oversize punch holder:

1. 228 punch tooling can be installed in either the punch

station or the opposite, open station end of the Ironworker.

Remove existing tooling or debris from installation site.

2. Install 228 punch block/stem assembly to the moving

center with hardware provided. Tighten assembly to

moving center.

3. Insert 228 punch in CNUT228 coupling nut and thread

onto oversize punch block /stem assembly. Tighten with

wrench provided. If using a shaped punch, align the

locating keystock of the punch with the corresponding

slot within the punch stem assembly and tighten the

punch nut with the wrench.

Install the 419 oversize pedestal die table:

1. Clear the Ironworker base table of any debris.

2. Install the 419 die table with the die opening facing away

from the Ironworker. Align the slotted holes of the die table

with the base table holes and insert hardware provided.

3. With die table hardware loosely installed, insert 419 die

into die holder and secure with set screw.

4. Turn Ironworker on and inch down the punch to meet the

die with the foot pedal jog control. Check to see that the

punch is centered within the die.

5. Once punch is aligned with die, turn off power to machine;

secure the die table to the Ironworker base table by

tightening the hardware provided.

6. Install the oversize punch stripper assembly to the

Ironworker frame with the hardware provided.

7. Swing the stripper bar into place allowing for minimal

clearance between the top of the material to be punched

and the bottom of the stripper and tighten the stripper bar

bolts.

Safe Operation

Observe the following guidelines when operating the Oversize

Punch tooling.
• Follow manufacturer punch and die clearance and

tonnage recommendations as shown in Figure 2, page

21.

• Never exceed the capacities of the machine or tooling

as described in the specifications or listed at the tooling

station.

• The thickness of the material you are punching should not

exceed the diameter of the punch being used.

• Check punch and die alignment after every tooling

change.

• Adjust the punch stripper supplied with your Cleveland

Steel Tool Ironworker to allow for material positioning and

material stripping.

• Do not stack material to punch in the punching station.
• Use 1 - 2 drops of oil at the punch to aid in stripping

material from the punch as well as to extend the life of the

punch tooling.

• Punch complete holes only – partial holes will side load

the punch tooling and could result in punch breakage and

operator injury.

• Use punch aids when working small items at the punch

station.

Oversize Punch Tooling Operation

Clear the punch station of any tools or debris prior to powering

the machine on.
1. Place the material to be punched between the punch

and die. Check to see that your material is spanning the

stripper plate and that adequate material is avaiable to

safely position the material.

2. Clear your hands from the working area and depress the

foot pedal to move the punch through the material and

into the die.

3. When the punch is complete, release the foot pedal to

automatically strip the material from the punch and return

the punch to its neutral position. When the punch is

complete, release the foot pedal to automatically strip the

material from the punch and return the punch to its neutral

position.

Image Note: Guarding removed for clarity

Optional Tooling - Oversize 228 Punch and 419 Die Assembly

Guarding removed for clarity

Содержание 55 Ton













































Результаты поиска

Содержание 55 Ton

Отзывы:

Бренды по названию

Популярные бренды

Cleveland Steel Tool 55 Ton, Руководство пользователя

Результаты поиска

Содержание 55 Ton

Отзывы:

Бренды по названию

Популярные бренды