Cleco 116GLB-135A, Руководство по эксплуатации и обслуживанию

Страница: 2 / 12

2
Safety Recommendations
For your safety and the safety of others, read and understand the
safety recommendations before operating any grinder.
Always wear protective equipment and clothing.
Caution: Faceshields do not provide unlimited protection against
flying particles and are not to be considered as eye protection. ANSI
Z87.1 states that separate eyewear shall be used. For additional
information on eye protection, refer to Federal OSHA Regulations,
29 CFR, Section 1910.133, Eye and Face Protection, and ANSI
Z87.1, Occupational and Educational Eye and Face Protection. This
standard is available from the American National Standards Insti-
tute, Inc., 11 West 42nd Street, New York, NY 10036.
Hearing protection is recommended in high noise areas (above 85
dBA). Close proximity of additional tools, reflective surfaces, proc-
ess noises, and resonant structures can substantially contribute to
the sound level experienced by the operator. Proper hearing conser-
vation measures, including annual audiograms and training in the
use and fit of hearing protection devices may be necessary. For
additional information on hearing protection, refer to Federal OSHA
Regulations, 29 CFR, Section 1910.95, Occupational Noise Expo-
sure, and American National Standards Institute, ANSI S12.6,
Hearing Protectors.
• Gloves and other protective clothing should be worn as
required, unless they create a greater hazard.
• Do not wear loose fitting clothing, or clothing that may
restrict movement, become entangled or in any way
interfere with the safe operation of the grinder.
Grinding or other use of this tool may produce hazardous fumes
and/or dust. To avoid adverse health effects utilize adequate venti-
lation and/or a respirator. Respirators should be selected, fitted,
used and maintained in accordance with Occupational Safety and
Health Administration and other applicable regulations. Read the
material safety data sheet on any materials involved in the grinding
process.
Cleco grinders are designed to operate on 90 psig (6.2 bar) max.
air pressure. If the tool is properly sized and applied, higher air
pressure is unnecessary. Excessive air pressure increases the
loads and stresses on the tool parts and may result in breakage.
Installation of a filter-regulator-lubricator in the air supply line is
highly recommended.
Before the tool is connected to air supply, check throttle for proper
operation, i.e., throttle moves freely and returns to closed position.
Being careful not to endanger adjacent personnel, clear air hose of
accumulated dust and moisture. Use protective barriers where
necessary — hot sparks can burn. Barriers also help reduce noise
levels. Before removing tool from service or changing accessories,
make sure air line is shut off and drained of air. This will prevent tool
from operating if throttle is accidently engaged. Do not use tool to
drain residual air from air line, instead use of a self-relieving valve
located near tool is highly recommended.
The speed rating and warning information on the tool should be
maintained or replaced for legibility in the event of damage. Before
installing an accessory or a grinding wheel, after all tool repairs, and
whenever a grinder is issued for use, check the free speed of the
tool with a tachometer to make sure actual free speed at 90 psig
does not exceed rated free speed stamped on tool. Grinders in use
on the job must be checked at least once every 20 hours of operation,
or once a week, whichever is most frequent.
Guard (if wheel type grinder) must be securely attached to the
grinder with the bolt, nut and lockwasher in place and torqued to 30-
40 in. lbs.
INSPECT GRINDING WHEEL OR ACCESSORY
Fragments from a grinding wheel, mounted wheel or carbide burr
that breaks or comes apart while rotating can cause serious
injury or even death. Inspect grinding wheel or accessory. Check
the maximum safe RPM marked on wheel, accessory or package.
Never use wheels or accessories rated at or below actual tool
speed. Cracked, dropped, faulty, or bent accessories are danger-
ous. Suspect accessories should not be used and should be
disposed of. Look for cracks, chips, water stains, or signs of abuse
or improper storage. Causes of grinding wheel failures have been
traced to such factors as:
• Dropping, bumping, or abuse (careless handling of the
grinder)
• Improper mounting
• Imbalance
• Improper shipment or storage, or age
• Mismatched speed ratings
• Exposure to water, solvents, high humidity, freezing, and
extreme temperatures
WARNING !
Impact resistant eye protection
must be worn while operating
or working near this tool.
CAUTION !
Personal hearing protection is
recommended when operating
or working near this tool.
WARNING !
Wear respirator where
necessary.
WARNING !
Fragments from an abrasive wheel
can cause serious injury or death.
Do not operate without proper
wheel guard in place.
1
2
3
4
5
6
0
202409
WARNING AND
INSTRUCTION LABEL
OVER
CAUTION
!
Personal hearing protection is recommended when operating or working near this tool.
WARNING
!
Impact resistant eye protection must be worn while operating or working near this tool.
Read Operating Instructions carefully. Follow the Safety Recommendations for your safety and the safety of others. Hearing protection is recommended in high noise areas (above 85 dBA). Close proximity of other tools, reflective surfaces, process noises, and resonant structures can substantially contribute to the sound level experienced by the user.
WARNING
!
Repetitive work motions and/or vibration can cause injury to hands and arms. Use minimum hand grip force consistent with proper control and safe operation. Keep body and hands warm and dry. Avoid anything that inhibits blood circulation. Avoid continuous vibration exposure. Keep wrists straight. Avoid repeated bending of wrists and hands.
Do not remove this tag until the operator of this tool has read these safety precautions.
202101 & 869974
WARNING TAGS
Cleco
MODEL
SERIAL NO.
CAUTION
TACHOMETER
203185
CAUTION LABEL