manualshive.com logo in svg

CleaverBrooks CBEX Elite, Эксплуатация и обслуживание

Поделиться
Скачать
CleaverBrooks CBEX Elite Скачать руководство пользователя страница 82

Inspection and Maintenance

8-10

750-368

CBEX Elite 100-1200 HP

If at any time the burner flame appears “stringy” or “lazy,” it is possible that the nozzle tip or swirler has become 
partially clogged or worn. Any blockage within the tip will cause the air pressure gauge to increase above its nor-
mal value.

FIGURE 8-7.

Standard and High Turndown Oil Nozzle Components

Disassemble with the power off by unlatching and withdrawing the burner gun. Insert the nozzle body into the 
hanger vice and use the spanner wrench to remove the tip. Remove the swirler and seating spring being careful 
not to drop or damage any parts.

Perform any necessary cleaning with a suitable solvent. Use a soft fiber brush or pointed piece of soft wood for 
cleaning. Do not use wire or a sharp metallic object, which could scratch or deform the orifices as well as the 
precision ground surfaces of the swirler and tip. Inspect for scratches or signs of wear or erosion, which may 
make the nozzle unfit for further use. Take the necessary precautions in working with solvents.

The tip and swirler are a matched set, which are precision lapped at the time of assembly. The close fit of the 
lapped surfaces must be maintained in order to provide optimum performance. Additional lapping may be 
required to provide better atomization for more efficient combustion. Do not interchange parts if a spare is kept. 
In reassembling, be certain that the seating spring is in place and that it is holding the swirler tightly against the 
tip. The swirler is stationary and does not rotate, but rather imparts a swirling motion to the oil.

See that the plugged hole is at the bottom of the nozzle body when the gun is installed.

8.7.3 — Cleaning the Back Pressure Orifice Nozzle

Clean the strainer screen carefully to remove any foreign matter. Use suitable solvents in cleaning. Hot water at 
high velocity is also helpful in cleaning. Replace strainer by screwing it into the nozzle body only finger tight. Do 
not use an orifice of a size other than originally installed.

FIGURE 8-8.

Back Pressure Orifice

Содержание CBEX Elite







































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды