ClearSpan 104137 Скачать руководство пользователя

Страница: 2 / 31

CLEARSPAN

™

HIGH TUNNELS AND CANOPIES

Revision date: 01.28.09

YOU MUST READ THIS DOCUMENT BEFORE YOU

BEGIN TO ASSEMBLE THE SHELTER

Thank you for purchasing this ClearSpan™ shelter. When

properly assembled and maintained, this product will

provide years of reliable service. These instructions include

helpful hints and important information needed to safely

assemble and properly maintain the shelter. Please read

these instructions

before

you begin.

If you have any questions during the assembly, contact

Customer Service for assistance.

SAFETY PRECAUTIONS

•  Wear eye protection.
•  Wear head protection.
•  Wear gloves when handling metal parts.
•  Use a portable GFCI (Ground Fault Circuit Interrupter)

when working with power tools and cords.

• Do not climb on the frame during or after construction.
• Do not occupy the structure during high winds,

tornadoes, or hurricanes.

• Provide adequate ventilation if the structure is

enclosed.

• Do not store hazardous materials in the structure.
• Provide proper ingress and egress to prevent

entrapment.

LOCATION

Choosing the proper location is an important step before

you begin to assemble the structure.

The following suggestions and precautions will help you

determine whether your selected location is the best

location.
• Never erect the structure under power lines.
• Identify whether underground cables and pipes are

present

before

preparing the site or anchoring the

structure.

• Location should be away from structures that could

cause snow to drift on or around the building.

• Do not position the structure where large loads such as

snow and ice, large tree branches, or other overhead

obstacles could fall.

SITE

After choosing a location, proper preparation of the site is

essential. Follow the information below.
•

A level site is required

. The site must be level to

properly and safely erect and anchor the structure.

• Drainage: Water draining off the structure and from

areas surrounding the site should drain away from the

site to prevent damage to the site, the structure, and

contents of the structure.

WARNING:

The individuals assembling this structure

are responsible for designing and furnishing all

temporary bracing, shoring and support needed during

the assembly process. For safety reasons, those who

are not familiar with recognized construction methods

and techniques must seek the help of a qualified

contractor.

Содержание 104137
































Результаты поиска

Содержание 104137

Отзывы:

Похожие инструкции для 104137

Бренды по названию

Популярные бренды

ClearSpan 104137, Руководство пользователя

Результаты поиска

Содержание 104137

Отзывы:

Похожие инструкции для 104137

Бренды по названию

Популярные бренды