Configuration
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
DIP switch configuration
Located on the rear of the receiver are five DIP switches. These switches are default
programmed at the factory to allow the receiver to operate without adjustment
when it is connected to one of the RS-485 Remote Panel ports on the rear of the
ClearOne conferencing unit.
If you are connecting the IR Remote receiver to a network of ClearOne Control
Panels (which are connected to one of the Remote Panel ports),
ensure that DIP
switch 5 is set to on
; this serves as the termination of the daisy chain, since the IR
Remote is always connected as the last device in the chain. Set DIP switches 1–4
according to the table in Figure 5.
As an example, if you have three Control
Panels connected to Remote Panel A and you want
to connect an IR Remote receiver to the daisy
chain, the receiver would be number 3 (the Control
Panels being numbers 0, 1, and 2). Therefore, the
DIP switch settings for the IR receiver would be
1=Off, 2=Off, 3=On, 4=On, and 5=On.
Always connect the IR Remote receiver to the last Control Panel when connecting to
a daisy chain of Control Panels. Only the last device in a daisy chain should have the
last DIP switch set to On (to terminate the chain).
5
Installation
4
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Front Panel LEDs
There are three LEDs on the front of the XAP IR Remote—Mute, In Use, and
Ready.
•
Mute.
The Mute LED flashes red when microphones are muted (default). You
can program this LED to illuminate to another command in the Remote
Builder window of G-Ware. See Configuration (below) for more information.
•
In Use.
The In Use LED glows red whenever a phone participant is on the
line. The programming of this LED cannot be changed.
•
Ready
. The Ready LED glows red when the receiver is connected to a XAP or
PSR1212 product, indicating the system is ready for a valid command. The
programming of this LED cannot be changed.
When a button is pressed, the Ready LED flashes, indicating a command has been
received.
=
Microphone
VOLTAGE RANGE 100V-240V 2A
FREQUENCY 50Hz/60Hz
OUTPUT 5
OUTPUT 6
OUTPUT 7
OUTPUT 8
INPUT 5
INPUT 6
INPUT 7
INPUT 8
OUTPUT 1
OUTPUT 2
OUTPUT 3
OUTPUT 4
MIC 1
MIC 2
MIC 3
MIC 4
SPEAKER
3
2
4
1
MUTE IN USE
READY
Speaker Connection
10W, 4 to 16Ω
XAP IR Receiver
Analog
Telephone
Line
Telephone
Set
XAP 400
Figure 4. Typical XAP IR Remote Receiver installation
✍
0
1
2
3
4
5
6
7
8
9
10
11
IR Remote Receiver Number
1
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
2
On
On
Off
Off
On
On
Off
Off
On
On
Off
Off
3
On
On
On
On
Off
Off
Off
Off
On
On
On
On
4
On
On
On
On
On
On
On
On
Off
Off
Off
Off
5
On
On
On
On
On
On
On
On
On
On
On
On
DIP Switch
Figure 5. DIP switch settings
Programming Functions
The XAP IR Remote Control is programmed by default to operate a single XAP 400
with an amplifier and speaker connected to Output 8; however, it is easy to cus-
tomize should you require different specifications. If you want to use the factory
defaults, proceed to Operation on page 12. Below are instructions for setting up the
remote control in ClearOne G-Ware software, the user interface for XAP products.
XAP IR Remote system defaults
The XAP IR Remote is programmed by default to operate the XAP 400/TH2
Telephone Interface as follows: The On, Off, 0-9, *, #, Flash, Redial, Speed Dial,
and Conference Call keys activate any XAP 400/TH2 on the expansion bus network
regardless of its type and device ID. This is because of the default ** programming,
which allows the selection of any device on the network.
Buttons programmable in G-Ware are illustrated in Figure 12 (page 12).
Configuration
✍