manualshive.com logo in svg

Clearfield StreetSmart Pre-Assigned FDH, Руководство по установке, Страница: 7 / 17

Поделиться
Скачать
Clearfield StreetSmart Pre-Assigned FDH Скачать руководство пользователя страница 7

7

StreetSmart Pre-Terminated FDH Cabinet

__________________________________________________________

Installation Manual

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeClearfield.com • [email protected] 

Manual 021814 REV A - Jan 2021

Pole Mount Installation

1.

Locate the hoist plate and install, using the included hardware, to the top of the cabinet on the side that will be 

closest to the pole.

2.

Locate the toothed bracket that has the mounting holes in the flange and mount it to the cabinet (below the previously 

installed hoist plate) using the included hardware.

3.

Determine the top height of the cabinet. Drill a 5/8” hole 8 inches below the anticipated height of the cabinet, all the way 

through the pole.

Note:

 Clearfield does not provide the mounting hardware. Required hardware includes a 5/8” threaded rod (3” longer than 

pole diameter), washers, lock washers, nuts and Lock Tight (red).

Note: 

288 PON FSC cabinet shown for reference. Pre-Terminated FDH cabinet will be mounted to the pole using the same 

method.

Содержание StreetSmart Pre-Assigned FDH


















Отзывы:

Нет отзывов