Clear-Com ENCORE AMS-1027 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 30

Clear-Com ENCORE AMS-1027 Скачать руководство пользователя страница 10

A M S - 1 0 2 7 A M P L I F I E D S P E A K E R S T A T I O N

1 - 4

Internal Speakers

The AMS-1027’s internal speaker system is comprised of two mid/high-range
speakers (left and right) and one woofer speaker (center). The two side channel
speakers reproduce, in stereo, only the mid and high frequencies, while the center
woofer speaker reproduces the low frequencies summed from both the left and
right channels.

Volume Control

The volume-control knob adjusts the loudness of the audio reproduced by the
internal speakers or connected headphone.

Audio Level Bargraph Meter Displays

Audio levels for the left and right channels are displayed via two 10-segment
LED bargraph meters on the respective sides of the front panel. Dynamic range
for these meters is 23 dB. Gain calibration for these meters is via two recessed
trim pots on the rear panel (see “Rear Panel Connectors and Controls” later in
this chapter for more information). Meters are factory set for VU mode and gain
at 0 = +4 dBu.

Power Indicator LED

The power indicator LED signals the operating condition of the power supply.
The LED glows green to indicate the AMS-1027 is connected to mains power
and an operating voltage is present.

Headphone Jack

For critical listening or for listening in high noise environments, use the stereo
headphone feature rather than the internal speakers. The left and right channels
are separated for stereo listening in the headphones. When you plug in
headphones, the internal speakers will mute. This jack accepts the standard
1/4-inch tip-ring-sleeve stereo plug.

Balance Control

This control pans the volume balance between the left and right speakers. If the
balance is adjusted hard left or right, a slight L+R channel mix is retained (only
in low bass frequencies) so that phase discrepancies can be discerned.

Separate left and right volume controls may be selected via internal jumpers in
lieu of a balance control. For instructions on how to perform this retrofit, see
“VOL/BAL to A-VOL/B-VOL Retrofit Instructions” on page 1-6.

1

2

3

4

5

6

The AMS-1027’s front-panel

controls and indicators are

illustrated in Figure 1-3.

«
...
8
9
10
11
12
...
»

Содержание ENCORE AMS-1027































Отзывы:

Нет отзывов