Clean Water Systems 7500-S Скачать руководство пользователя страница 12

Страница: 12 / 16

Page 12

7500-S Carbon Backwash Filter Guide

www.cleanwaterstore.com

rev102418

Programming Overview

Note: Indicator locations may vary between models

Menu/Confirm

10. Scroll down

Return/Immediate Backwash Start

11. Minutes

Icon Indicating Programming Mode

12. Button Lock

Power Indicator

13. Fast Rinse

Time of day

14. Not used

Not Used

15. Not used

Not Used

16. Backwash

Days remaining Until Backwash

17. In Service/Working

Scroll up

18. Backwash cycle in process

IMPORTANT:

Before any operation, the valve menu must be unlocked. Press and

hold both the Up and Down buttons for approximately 5 seconds.

A sound will indicate the menu is unlocked. The menu will re-lock automatically

after 1 minute of inactivity.

Digital Display Icons and the four Service Buttons:

In addition to the Dynamic

Display Stipe (explained below) there are eight digital icons on the display that

will indicate “where the valve is”. They are as follows (left to right, top row

bottom row):

Содержание 7500-S

















Результаты поиска

Содержание 7500-S

Отзывы:

Похожие инструкции для 7500-S

Бренды по названию

Популярные бренды

Clean Water Systems 7500-S, Руководство пользователя

Результаты поиска

Содержание 7500-S

Отзывы:

Похожие инструкции для 7500-S

Бренды по названию

Популярные бренды