Clayton WartHog WGX Series Скачать руководство пользователя страница 5

Страница: 5 / 18

Repair or Warranty Contact

Clayton Associates, Inc. • 1650 Oak Street • Lakewood, New Jersey 08701 • P.+1-732-363-2100 F.+1-732-364-6084

WGX-4

www.DustlessMadeSimple.com

•

[email protected]

Page 5

Install a new HEPA filter.

•

Holding the power head on its side, screw the new HEPA filter onto the filter adapter.

•

Verify the white inner ring of the HEPA filter is fully seated against the underside of the power head.

–

If it is not, rotate it clockwise until it is seated.

• Refer to the instructions included with the HEPA cable lock to install the cable lock.

4. Attach the power head.

• Position the power head on the tank.
• Rotate the power head so that the compressed air control valve on the power

head is aligned with the inlet port on the vacuum tank.

• Latch the power head to the tank.

Activate the HEPA filter timer.

• Attach the new HEPA timer card with a zip tie (included) to the top handle of the

vacuum.

• Follow the directions on timer card to activate it.

The vacuum has the following compressed air requirements to function properly:

• Compressed air must be clean, dry, and oil free to prevent blockage of the pneumatic system.
•

Compressed air line and fittings must have a minimum diameter of 1/2 in (13 mm).

Compressed Air Plug (Air In)

•

The vacuum is supplied with a 1/2 in (13 mm) industrial interchange compressed air plug for connection to a compressed air supply.

The Compressed Air Plug may be changed to another nominal 1/2 in (13 mm) style if required.

•

Hold the brass bulkhead fitting with a 11/4 in (32 mm) open end wrench.

•

Remove the compressed air plug with either a 7/8 in (22 mm) deep socket or open end wrench.

• Install a new compressed air plug.

1. Attach the vacuum hose.

• Open the inlet port on the vacuum tank.
• Insert the metal sleeve of the vacuum hose into the inlet port on the vacuum tank.

2. Activate the vacuum.

• Rotate the Compressed Air Control valve to the ON position.

GETTING STARTED

WGX-4_003

Inlet Port

aligned with …

Compressed Air

Control Valve …

COMPRESSED AIR FITTINGS

BEFORE EACH USE

Содержание WartHog WGX Series



















Результаты поиска

Содержание WartHog WGX Series

Отзывы:

Похожие инструкции для WartHog WGX Series

Бренды по названию

Популярные бренды

Clayton WartHog WGX Series, Безопасность, эксплуатация и обслуживание

Результаты поиска

Содержание WartHog WGX Series

Отзывы:

Похожие инструкции для WartHog WGX Series

Бренды по названию

Популярные бренды