background image

5

AXCOR WASH 300

CONTROL PANEL

Continue

Switching on the projector - Fig. 8

Press the switch. The projector starts resetting the effects. At the same time, the following information scrolls on the display:

                                         Model                                      Firmware                             Axcor Wash 300                    System errors

                                                         Axcor Wash                           Version X.X.X                      Dmx Address xxx                 E: .........................
                                                         300                                          Date                                                                                    W: .........................

On conclusion of resetting in case of absence of the dmx signal, Pan and Tilt move to the “Home” position (Pan 128 bit - Tilt 128 bit). The control panel
(Fig. 8) has a display and buttons for the complete programming and management of the projector menu. The display can be in one of two conditions:
rest status and setting status. When it is in the rest status, the display shows the projector’s DMX address.
During menu setting status, after a wait time (about 30 seconds) without any key having been pressed, the display automatically returns to rest status.
It should be noted than when this condition occurs, any possible value that has been modified but not yet confirmed with the 

F

key will be cancelled.

1

Dmx Address

Warning Message

 

 

8

Connecting to the control signal line (DMX) - Fig. 7
Use  a  cable  conforming  to  specifications  EIA  RS-485:  2-pole  twisted,  shielded,  120Ohm  characteristic  impedance,  22-24  AWG,  low  capacity.  Do  not  use
microphone cable or other cable with characteristics differing from those specified. The end connections must be made using XLR type 5-pin male/female
connectors. A terminating plug must be inserted into the last projector with a resistance of 120Ohm (minimum 1/4 W) between terminals 2 and 3.
IMPORTANT: The wires must not make contact with each other or with the metal casing of the connectors. The casing itself must be connected to the
shield braid and to pin 1 of the connectors.

 

 

 

 

 

 

SIGNAL

SCREEN

DMX 512

5 PIN

1

2

3

4

5

SIGNAL

Mains

6

7

Connecting to the mains supply - Fig. 6

NB: connecting 
one Axcor Wash 300 
to the mains,
it is possible to connect up
to a maximum 
8 @ 200-240Vac 
or 3 @ 100-120Vac 
Axcor Wash 300 in parallel
at the same time.

DMX 512

Содержание AXCOR WASH 300













Отзывы: