Check that the voltage, frequency and power of the mains electricity supply correspond with
those shown on the electrical specification plate.
- Important: it is mandatory to connect the unit to a power system equipped with an
efficient earth connection (Class I equipment).
• Power uptake
See paragraph 7 TECHNICAL DATA.
After completing the above steps, press the switch (I) and check that the projector works
properly.
• Unpacking
Open the cardboard box, remove the pro-
jector from the packing and place it on a
flat surface.
Remove from the packing all the compo-
nents supplied as standard (optional la-
bels, effects guides, objective support, ob-
jective, mounting, screws, tools, etc.)
Locate the lamp change label (1) and, if
necessary, replace it with one of the op-
tional multi-lingual labels.
Make certain that the label is never re-
moved, as it contains important safety
information.
• Assembling the projector support
Position the mounting (2) on the plates (3)
according to the desired height, insert the
bushing (4), the countersunk washer (5)
and the screw (6) in the hole you have
chosen and secure with the setscrew
wrench supplied.
Adjust the projector support to the desired
position and secure it by means of the
knobs (7).
The mounting can also be fitted towards
the bottom of the projector by inverting the
position of the graduated plates (3).
• Fitting the lamp
If the projector is not supplied with the
lamp already fitted, refer to the instruc-
tions on lamp changing in section 5 MAIN-
TENANCE.
• Installing the projector
The unit must be fixed exclusively with the
appropriate support, by means of the hole in the mounting. You are advised to use a ø10 bolt
complete with nut and snap ring. Make certain that the anchoring point is stable before po-
sitioning the projector, and fix it with the appropriate mounting only.
The projector can be fixed in any position without affecting its operating characteristics.
The unit may be fitted on normally inflammable surfaces.
• Minimum distance from illuminated objects
The projector must be positioned in such a way that objects struck by
the light beam are located at least 0.8 metres from the projector ob-
jective.
The stipulated minimum distance of inflammable materials from any point of the projector hous-
ing is 0.10 metres.
Caution:
For better and more reliable operation of the unit, the ambient temperature must not exceed
35°C.
Protection class IP 20: the unit is protected against the penetration of solid bodies with a diame-
ter of more than 12 mm (first figure 2) and can be damaged by spring seepage, rain, spray and
water jets (second figure 0).
• Connecting to the mains electricity supply
The projector must be supplied with the voltage/frequency marked on the back of the projector.
5
V.I.P. S.I.P.
INSTALLING THE PROJECTOR
1
POWER SUPPLY AND FINE ADJUSTMENT
2
• Fitting the objective
Insert the objective (9) in its support (10)
and tighten the knob (11). Rest the
assembly on the effects guides and
secure it by pressing the fixing springs
(12) in the direction shown in the figure.
In addition to the standard objective,
optional objectives and a wide range of
effects are also available (see section 9).
For safety reasons, the effect guides on
the V.I.P. projector are electrified at very
low voltage (24Vac) and protected against
short circuiting. This enables you to install
the motorised effects described in section 9.
• Centring the projector
Slacken the knobs (7) and move the projector along the mounting (2) until the light beam is
positioned at the desired point, and then tighten the knobs (7).
Adjust the objective and/or objective holder, moving them axially until the circle of light is
perfectly focused.
POSITIONING THE PROJECTOR
3
INSTRUCTION MANUAL
ENGLISH
V.I.P. HTI 300
V.I.P. 250 HAL
S.I.P. 300 HAL
®
PROFESSIONAL SHOW LIGHTING
Caution
Read every part of this instruction manual carefully. For correct and safe use of this
equipment, it is essential to be fully conversant with the information and instructions set
out in this manual.
0.8
1
2
4
3
5
6
7
I
L
N
L
N
S.I.P. 300 HAL
V.I.P. 250 HAL - V.I.P. HTI 300
Mains
Mains
10
11
9
12
8
