Clatronic KA 3459 T, Инструкция по эксплуатации

Страница: 20 / 36

20
Supplied parts
1 Coffee / tea maker
1 Filter holder
1 Permanent ilter
1 Cup shelf
1 Drip tray
1 Stainless steel thermo cup
1 Glass cup
Initial Operation of the Device
1. Remove all packaging and transportation safety devices
from the device that may be present.
2. Rub all of the parts with a damp cloth. This will remove any
dust that may have accumulated during transport.
3. Clean the ilter holder, the permanent ilter and the cups in
a bowl of water.
4. Reinsert all of the parts in the reverse order.
NOTE:
Before brewing beverages for the irst time, run water through
the appliance four times to clean it.
• Pour 300 ml fresh water into the water tank.
• Place the cups on the cup shelf.
• Turn the selector to
“COFFEE”
.
• When the cup is full, turn the selector to
“OFF”
and pour
the water away.
• After illing the water tank twice, turn the selector from
“COFFEE”
to
“HOT WATER”
.
Electrical Connection
NOTE:
Please ensure that the device is switched off. The switch
must be on
“OFF”
.
Insert the mains plug into a properly installed socket with earth-
ing contact. For information please see the type plate on the
device.
The red indicator lamp indicates that the power supply is on.
Operation
Preparing coffee or hot water
NOTE:
• The coffee ilter is located on the left hand side.
• The hot water spout is on the right hand side.
• You can pour up to 300 ml of water into the water tank to
brew 2 – 3 consecutive cups of coffee or tea.
1. Open the water tank cover.
2. Pour cold water into the water tank.
NOTE:
• To ill the water tank with the correct amount of water,
use the cup which you then want to use for brewing
the beverage.
NOTE:
• The coffee powder will absorb water. The amount
of coffee is thus somewhat less than the original
amount of water.
CAUTION:
Do not overill the water tank! Do not ill beyond the MAX
(300 ml) mark.
3. Close the water tank cover.
4. To prepare coffee, pull out the ilter holder. Pour the coffee
into the permanent ilter (approx. 6 g for one cup, max.
12 g according to personal taste). Slide the ilter holder
back under the ilter. The holder must audibly click into
place. Place a cup onto the cup shelf under the coffee ilter.
5. To prepare an infusion with hot water, place a cup under
the right hand spout.
6. Select the type of preparation:
a) For coffee, turn the selector to
“COFFEE”
.
b) For hot water, turn the selector to
“HOT WATER”
.
The brewing process begins. The green indicator lamp
lights up.
NOTE:
The brewing process for one cup of 125 ml lasts around
3½ minutes. It ends when the water in the tank has been
used up.
7. If you want to cancel or end the brewing process, turn the
selector to
“OFF”
. The green indicator lamp goes out.
8. After the brewing process, you can remove the cup. Watch
out for dripping.
WARNING:
Cold water on the hot heating element may splash and
injure you!
Allow the appliance to cool for 3 minutes, before reilling
the water tank.
End of use
1. Turn the selector to
“OFF”
. The green indicator lamp goes
out.
2. Disconnect from the mains. The red indicator lamp goes
out.
Descaling
It is necessary to descale the coffee machine if the preparation
time becomes considerably longer.
• Only a commercially available decalciier on a citric acid
base should be used for descaling.
• Please use the quantities stated on the pack or instruction
lealet. Do not exceed to maximum volume of water!
• Place the cups or another suitable vessel (for around
300 ml) onto the cup shelf.