EN
GL
IS
H
34
Ill. 4
2. Inlet filter
The inlet filter is to be found in the
dust filter compartment - see the
arrow. Press the button to release
the dust container and then remove
it. Pull the filter out towards the
front. Clean the inlet filter ap-
proximately every tenth time the
dust container is emptied, or more
frequently if necessary.
Please
ensure that the filter is always
clean, as otherwise air circula-
tion cannot be guaranteed.
If
necessary, the filter can also be
washed in warm water without any
additives. Place it back into place
only once it is completely dry!
Ill. 5
3. Outlet filter
The appliance is also equipped
with an outlet filter. In order to en-
sure that the filter works correctly,
we recommend that you replace
it every six months. It is located
on the rear part of your appliance
behind a ventilation grid. Open
the ventilation grille by pressing
the lever on its side. Then pull the
grille out towards the front. Remove
the filter and clean as described
above. Fit the filter back into place
and close the ventilation grid by
following the steps above in the
opposite order.
Important note!
Cleaning may become necessary after a shorter time, depend-
ing on the conditions of use, e.g. when vacuuming fine dust.
If the suction power of your vacuum cleaner diminishes please
clean the filters as described.
If the suction power suddenly diminishes during operation this
may be due to the filters being locked.
Cleaning and storage
Cleaning
• Pull the plug out of the socket before cleaning!
• Clean the casing with a dry cloth.
• Clean the motor protection filter approximately every 3.
time the vacuum cleaner is emptied. Clean the filter in hot
water without additives. Put it back into place only once it is
completely dry.
Storage
• Let the iron cool down completely.
• Wind the cable completely.
• Please position the device horizontally and insert the hook
on the telescopic tube into the parking aid (7) on the back of
the device.
Troubleshooting
• The Device Does Not Work.
Remedy:
Check the connection to the mains.
Check the position of the switch.
• The device does not suck up anything.
Possible Cause:
The dust container or the filters are dirty.
Remedy:
Empty or clean the components.
Possible Cause:
There is a foreign body in the suction tube or the nozzle.
Remedy:
Check the accessories for foreign bodies.
Noise development
The sound pressure level in the ear of an operator (LpA) was
measured according to DIN EN ISO 3744.
Sound pressure level detected: 78.0 dB(A) (no limit)
Technical Data
Model: ...............................................................................BS 1281
Power supply: ................................................220-240 V, 50/60 Hz
Power consumption:
P
nom.
: ............................................................................ 1800 W
P
max.
: ............................................................................2300 W
Protection class: .............................................................................
Net weight: .........................................................................5.85 kg
This device has been tested according to all relevant current
CE guidelines, such as electromagnetic compatibility and low
voltage directives, and has been constructed in accordance with
the latest safety regulations.
Subject to technical changes without prior notice!
05-BS 1281.indd 34
23.03.11 12:01
Содержание BS 1281
