Clarke Strong-Arm CSA20F Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 20

background image

6

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

7. Fit the pressure gauge to the

connecting nut, sealing the
thread with PTFE tape.Check the
gauge is upright before tightening
the nut with a 19 mm spanner.

8. Make a small hole in the pressure

gauge safety bung with a short
pin or nail before use.

• Do not use a long nail as you may

damage the internal components
of the gauge.

9. Lower the ram through the hole in

the moving carriage and secure
in position using the locking collar.

10. Connect the hydraulic hose to the

ram cylinder, sealing the joint with
PTFE tape, and tighten using two
open spanners.

«
...
4
5
6
7
8
...
»

Содержание Strong-Arm CSA20F





















Отзывы:

Нет отзывов

Похожие инструкции для Strong-Arm CSA20F

Бренд: IBM Страницы: 7

Бренд: Gallagher Страницы: 98

Бренд: Caen Страницы: 17

Бренд: NSI Solutions Страницы: 10

Бренд: Performance Tool Страницы: 6

Бренд: Hilti Страницы: 138

Бренд: X-Tronic Страницы: 12

Бренд: M7 Страницы: 14

Бренд: Hama Страницы: 2

PowerPack PC100

Бренд: Waeco Страницы: 115

Бренд: Baileigh Страницы: 39

Бренд: Advanced Страницы: 16

Бренд: Baileigh Страницы: 24

SonnenProtect 1300-AU-IN-ATS

Бренд: Sonnen Страницы: 20

Бренд: SATA Страницы: 74

Бренд: NAL Страницы: 2

Бренд: Hilti Страницы: 15

Бренд: VOLTEQ Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды