Clarke SBR760 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 36

Clarke SBR760 Скачать руководство пользователя страница 20

20

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

MAINTENANCE

SCHEDULE

For optimum performance from your machine, follow this maintenance
schedule and refer to any specific instructions given in this section.

DAILY MAINTENANCE:

• Clean the machine.

• Tighten loose mounting bolts.

• Check/replace damaged rollers.

• Check/replace cracked or damaged brake fingers or receiver.

• Sharpen/replace dull or nicked shearing blades.

• Any other unsafe condition.

MONTHLY MAINTENANCE:

• Lubricate the gears and hand crank bushings.

SEMI-ANNUAL MAINTENANCE:

• Lubricate the roller bushings.

CLEANING

Cleaning the SBR760 is relatively easy. Use cloth and degreasing spirits to wipe
down the machine.

LUBRICATION

Keep your SBR760 properly lubricated to help ensure long life and smooth
operation of the machine.

«
...
18
19
20
21
22
...
»

Содержание SBR760





































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды