manualshive.com logo in svg

Clarke METALWORKER CHDBG500, Инструкция по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Clarke METALWORKER CHDBG500 Скачать руководство пользователя страница 6

6

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

7. NEVER leave the grinder unattended when it is connected to an electrical 

power supply. Switch off the grinder and unplug it before leaving.

8. ALWAYS check for damaged parts. Before further use of the tool, a guard 

or other part that is damaged should be carefully checked to determine if 
it would operate properly and perform its intended function. Check for 
misalignment or binding of moving parts, breakage of parts and any other 
condition that may affect the tool's operation. A part that is damaged 
should be properly repaired or replaced at an authorised service centre. 
Following this rule will reduce the risk of electric shock, fire or serious injury.

9. Gloves, manufactured to the current European safety standards should be 

worn when operating grinding equipment.

10. Eye protection manufactured to the current European safety standards 

should be worn when operating grinding equipment.

NOTE:

Bench grinders used in industrial environments may be subject to the 
requirements of The Provision and Use of Work Equipment regulations 
1992 (particularly regarding the training requirement of The Abrasive 
Wheels Regulations 1970) or other legislation. If in doubt seek advice.

Please keep these instructions in a safe place for future reference.

SAFETY SYMBOLS

Read instruction manual before use

This machine is not suitable for hand held use

Not permitted for wet grinding

Wear eye protection

Wear ear defenders

Wear protective gloves

Содержание METALWORKER CHDBG500

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды