Clarke METALWORKER 6480235 Скачать руководство пользователя страница 12

Страница: 12 / 16

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

MAINTENANCE

CLEANING

1. Keep the surface of your sharpener free of grit, dirt, and grease. Use soapy

water or non-toxic solvents. Do not use petroleum based solvents.

2. If the motor does not operate, it needs to be serviced or replaced by a

qualified technician.

SPECIFICATION

Model Number

CMPS1

Voltage

230 V @ 50 Hz

Operating Temperature

-15

C - + 40

Drill Bit Sizes And Type

3.0 mm to 10 mm HSS

Maximum Chisel Blade Width

51 mm

Duty Cycle

S3 15% (90 sec on, 510 secs off)

No Load Speed

6700 rpm

Sound Pressure Level (L

dB)

74 dB(A)

Guaranteed Sound Power (L

dB)

87 dB(A)

Dimensions (L x W x H)

192 x 143 x 116 mm plus removable
sharpening attachments

Weight 1.65

Содержание METALWORKER 6480235

















Результаты поиска

Содержание METALWORKER 6480235

Отзывы:

Похожие инструкции для METALWORKER 6480235

Бренды по названию

Популярные бренды

Clarke METALWORKER 6480235, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание METALWORKER 6480235

Отзывы:

Похожие инструкции для METALWORKER 6480235

Бренды по названию

Популярные бренды