manualshive.com logo in svg

Clarke KIT300B, Инструкция по эксплуатации и техническому обслуживанию, Страница: 3 / 16

Поделиться
Скачать
Clarke KIT300B Скачать руководство пользователя страница 3

3

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

COMPRESSED AIR EQUIPMENT

1. Compressed air can be dangerous. Ensure that you are thoroughly familiar 

with all precautions relating to the use of compressed air equipment.

2. Never direct a jet of compressed air at people or animals.

3. Always ensure that the equipment/tool being used has a safe working 

pressure exceeding the output pressure of the compressor that it is 
connected to.

4. Always ensure that the air supply is turned off at the tool outlet and vent all 

compressed air from the air hose and the equipment attached to it, before 
disconnecting air hoses or other equipment from your compressor.

5. Ensure all fixed air connections are properly sealed using teflon tape or 

pipe sealant.

6. Never exceed the operating pressure as stated in the specification.

7. We strongly recommend that items contained in this kit be used in 

conjunction with appropriate eye and face protecting goggles, glasses or 
spray masks available from most DIY and hardware stores.

SPRAY GUN SPECIFIC WARNINGS

1. Never spray paint close to any source of heat or flame.

2. Always ensure the spraying area has adequate fresh air ventilation.

3. Always make sure there is adequate ventilation. Do not spray in confined 

or enclosed areas.

4. Always wear a suitable approved breathing mask when spraying, to 

protect against inhalation of paint spray or fumes. An air feed mask may 
be required when spraying toxic types of paint. If in doubt, check with the 
paint manufacturer.

5. Always check the manufacturers data sheets on the paint products being 

sprayed for any particular hazards, and follow the manufacturers 
instructions. Take particular care if spraying isocyanate paints.

6. Always disconnect the spray gun from the air supply when it is not in use, 

and before any disassembly.

7. Always keep the spray nozzle in place when spraying.

8. Always thoroughly clean the spray gun after use.

9. In the case of injury, seek expert medical advice immediately.

 

Never

 

smoke while spraying or preparing paints, or spray near a naked flame, 
heat source and electric sparks. Many paints are flammable.

10. Never exceed the maximum input air pressure of 50 psi (3.5 bar).

Содержание KIT300B

















Отзывы:

Нет отзывов