2
SAFETY RULES
1. Know your machine. Read this manual carefully.
Learn the machine’s applications and limitations,
as well as specific potential hazards peculiar
to it.
2. Ground all machines. This machine is “Double
Insulated,” meaning that all outside metal parts
are insulated from electrical power. Double
Insulated tools are equipped with a polarized
plug. This plug will fit in a polarized outlet only
one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit,
contact a qualified electrician to install a
polarized outlet. Do not attempt to circumvent
this safety feature.
3. Avoid body contact with grounded surfaces such
as pipes, radiators, ranges, and refrigerators.
There is an increased risk of electric shock if
your body is grounded.
4. Do not expose tool to moisture. Don’t use this
machinery in damp or wet locations. Keep
out of rain.
5. Do not abuse cord. Never use the cord to carry
tools or pull the plug from an outlet. Keep cord
away from heat, sharp edges or moving parts.
Replace damaged cords immediately. Damaged
cords increase the risk of electric shock.
6. Remove adjusting keys or wrenches before
turning the tool on. A wrench or key that is left
attached to a moving part of the tool may result
in personal injury.
7. Keep work area clean and well lit. Cluttered or
dark work areas invite accidents.
8. Keep children away. All children should be kept
away from the work area. Never let a child
handle a tool without strict adult supervision.
9. Do not operate this tool if under the influence of
alcohol or drugs. Read warning labels on
prescriptions to determine if your judgment or
reflexes are impaired while taking drugs. If there
is any doubt, do not attempt to operate.
10. Use safety equipment. Eye protection should be
worn at all times when operating this machine.
Use ANSI approved safety glasses. Everyday
eyeglasses only have impact resistant lenses.
They are NOT safety glasses. Dust mask, non-
skid safety shoes, hard hat, or hearing
protection should be used in appropriate
conditions.
11. Wear proper apparel. Loose clothing, gloves,
neckties, rings, bracelets, or other jewelry may
present a potential hazard when operating this
machine. Please keep all apparel clear of
the machine.
12. Don’t overreach. Keep proper footing and
balance at all times when operating this product.
13. Always disconnect the machine before making
any adjustments, storing, servicing, or changing
accessories. Such preventative safety measures
reduce the risk of starting the tool accidentally.
14. Use clamps or other practical means to secure
and support the work piece to a stable platform.
Holding the work by hand or against your body
may lead to a loss of control.
15. Do not force tool. Use the correct tool for your
application. The correct tool will do the job better
and safer at the rate for which it was designed.
16. Do not use the tool if the switch does not turn it
on and off. Any tool that cannot be controlled
with the switch is dangerous and must
be repaired.
17. Check for damage. Check your tool regularly. If
part of the tool is damaged it should be carefully
inspected to make sure that it can perform its’
intended function correctly. If in doubt, the part
should be repaired. Refer all servicing to a
qualified technician. Consult your dealer
for advice.
18. Keep away from flammables. Do not attempt to
operate this tool near flammable materials or
combustibles. Failure to comply may cause
serious injury or death.
19. Do not start tool while tool is in contact with
work materials. Always turn tool on BEFORE
coming in contact with material surface.
20. Do not set tool down until it has come to a
complete stop.
21. Always check to make sure that trigger is not
engaged before plugging tool in. Tool may
cause damage to property or person if plugged
in while on.
22. Keep hands clear of blades.
23. Store idle tools out of the reach of children and
untrained persons. Tools may be dangerous in
the hands of untrained users.
24. Maintain tools with care. Keep tools sharp and
clean. Properly maintained tools, with sharp
cutting edges, are less likely to bind and are
easier to control.
25. Hold tool by insulated gripping surfaces when
performing an operation where the tool may
contact hidden wiring or its own cord. Contact
with a live wire will make exposed metal parts of
the tool “live” and could shock the operator.
