Clarke Contractor CR3 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 20

background image

16

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

MAINTENANCE AND CARE

CLEANING

• To ensure the best performance from the router, it must be kept

clean.

• Keep the cooling vents on the motor housing clean and

unobstructed at all times. Blow out any dust and dirt at regular
intervals.

GENERAL MAINTENANCE

• Make sure that all nuts, bolts and screws are tight and secure.

• Always have any damaged or worn parts repaired, or replaced.

• Always have your router inspected and maintained by qualified

service personnel. Do not attempt to repair the router unless you are
qualified to do so.

STORAGE

• Make sure that the router has been thoroughly cleaned before

storing it in a clean, dry place out of the reach of children.

LUBRICATION

• The bearings of the machine do not need lubrication, as they are

sealed.

• The two plunge columns on the routing base should be slightly oiled

from time to time.

ENVIRONMENTAL PROTECTION

Do not dispose of this product with general household waste. All
tools, accessories and packaging should be sorted, taken to a
recycling centre and disposed of according to the laws governing
Waste Electrical and Electronic Equipment.

«
...
14
15
16
17
18
...
»

Содержание Contractor CR3





















Отзывы:

Нет отзывов

Похожие инструкции для Contractor CR3

MMAC-Plus 9F106-02

Бренд: Cabletron Systems Страницы: 7

Бренд: iDirect Страницы: 60

Бренд: Ubiquiti Страницы: 40

Бренд: WaiLan Страницы: 27

4-Port 10/100Mbps Ethernet Broadband Router

Бренд: AOpen Страницы: 41

Бренд: Eicon Networks Страницы: 32

Бренд: Konig Страницы: 2

Бренд: Ubiquiti Страницы: 20

TE100S8P - Fast Ethernet Switch

Бренд: TRENDnet Страницы: 11

Бренд: Cradlepoint Страницы: 2

Бренд: ORiNG Страницы: 101

Бренд: NETGEAR Страницы: 10

Бренд: Cables to Go Страницы: 63

Бренд: Zonet Страницы: 45

Бренд: Allied Telesis Страницы: 128

Бренд: Acer Страницы: 70

Бренд: Acer Страницы: 94

Predator Connect W6

Бренд: Acer Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды