manualshive.com logo in svg

Clarke CIG91216, Руководство по сборке

Поделиться
Скачать
Clarke CIG91216 Скачать руководство пользователя страница 14

14

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

.

7. When the cover rails are all 

secured, tighten the end covers 
and the main cover to the end 
frames using the ratchet action.

NOTE: 

Over-tightening can cause 

damage to the end cover 
pockets. Do not over-
tighten. This should always 
be done with the front 
door panel closed.

8. Check periodically (two to three 

times in the first week) and tighten the ratchet tie-downs and all hardware 
as needed. You may need to remove and re-set the ratchet to allow for 

more strap material becoming wound around the ratchet spindle..

9. Open the door with the help of an assistant, rolling the fabric up until the 

door can be held in position above the opening using the webbing straps 
and buckles as shown above. (When not in use, tie the ends of the straps to 
the webbing loops provided for that purpose.)

WARNING: IF POSITIONING THE GARAGE IN A WINDY LOCATION 
ALWAYS ENSURE THE FRONT DOOR IS KEPT FULLY CLOSED TO PREVENT 
WIND LIFTING THE SHED FROM INSIDE.

Содержание CIG91216

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды