2
The Meter may be hung on a wall,
or supported as shown,
depending upon which support is
used.
The probes may be located as
shown, allowing easy one hand
operation.
GENERAL CHARACTERISTICS
Maximum Display
:1999 counts (3½ digits) with auto polarity
indication and eng. unit.
Measuring Method
: Dual-Slope integration A-D convertor
system.
Overrange Indication
: Figure “1” displayed on the LCD.
Max. common mode voltage
: 500V dc/ac rms.
Temp. for guaranteed accuracy : 23
O
C to ± 5
O
C.
Temperature Ranges
: Operating 0
O
C to 40
O
C, 32
O
F to 104
O
F.
: Storage-10
O
C to 50
O
C, 14
O
F to 122
O
F.
Power Supply
: 1x 9V battery (NEDA 1604, 6F22 type or
equiv).
Low Battery Indication
: - + On left of display.
Dimensions incl. Holster
: 201L x 100W x 55H mm.
Weight
: 478g (incl. 9 volt battery & holster).
Accessories
: Operating manual, set of test leads.
Holster,
PARTS & SERVICE TEL: 020 8988 7400
or e-mail as follows:
PARTS: [email protected]
SERVICE: [email protected]
For Spare Parts and Service, please contact your nearest dealer,
or CLARKE International, on one of the following numbers.
PARTS & SERVICE CONTACTS
11
MAINTENANCE
Battery and/or fuse replacement should only be done after the test leads
have been disconnected.
Battery and Fuse Replacement
Note the condition of the 9-volt battery using the procedure described
above. If the battery needs to be replaced, unscrew the four screws and
remove the back cover. Replace the spent battery with one of the same
type (
NEDA.1604, 6F22 or equiv
). The same procedure is used to replace
the fuses. Ensure replacements are of the same size and value as the original.
Replacement Parts.
1.
Test Leads (pair)
Part No. HYTL060
2.
Holster (Size A)
Part No. HYHT60
Fuse : F200mA / 250V (quick acting)
Temperature Measurement
1. Set the Function switch to
O
C position and the LCD display will show ambient
temperature.
2. Insert the ‘K’ type thermocouple into the TEMP socket and contact the object
to be maesured with the thermocouple probe. Read the display.
WARNING. To avoid an electric shock, ensure the therrmocouple has been
removed before changing to another function.
Frequency Measurement
1. Connect the BLACK test lead to the COM jack and the RED test lead to
the V
Ω
Hz jack
2. Set the Function switch to 20kHz and connect test leads across the source or
load under measurement.
NOTE:
1. Reading is possible above 10V rms, but accuracy is not guaranteed.
2. in a noisy environment, it is preferable to use shielded cable to measure small
signals.
2
The Meter may be hung on a wall,
or supported as shown,
depending upon which support is
used.
The probes may be located as
shown, allowing easy one hand
operation.
GENERAL CHARACTERISTICS
Maximum Display
:1999 counts (3½ digits) with auto polarity
indication and eng. unit.
Measuring Method
: Dual-Slope integration A-D convertor
system.
Overrange Indication
: Figure “1” displayed on the LCD.
Max. common mode voltage
: 500V dc/ac rms.
Temp. for guaranteed accuracy : 23
O
C to ± 5
O
C.
Temperature Ranges
: Operating 0
O
C to 40
O
C, 32
O
F to 104
O
F.
: Storage-10
O
C to 50
O
C, 14
O
F to 122
O
F.
Power Supply
: 1x 9V battery (NEDA 1604, 6F22 type or
equiv).
Low Battery Indication
: - + On left of display.
Dimensions incl. Holster
: 201L x 100W x 55H mm.
Weight
: 478g (incl. 9 volt battery & holster).
Accessories
: Operating manual, set of test leads.
Holster,
PARTS & SERVICE TEL: 020 8988 7400
or e-mail as follows:
PARTS: [email protected]
SERVICE: [email protected]
For Spare Parts and Service, please contact your nearest dealer,
or CLARKE International, on one of the following numbers.
PARTS & SERVICE CONTACTS
11
MAINTENANCE
Battery and/or fuse replacement should only be done after the test leads
have been disconnected.
Battery and Fuse Replacement
Note the condition of the 9-volt battery using the procedure described
above. If the battery needs to be replaced, unscrew the four screws and
remove the back cover. Replace the spent battery with one of the same
type (
NEDA.1604, 6F22 or equiv
). The same procedure is used to replace
the fuses. Ensure replacements are of the same size and value as the original.
Replacement Parts.
1.
Test Leads (pair)
Part No. HYTL060
2.
Holster (Size A)
Part No. HYHT60
Fuse : F200mA / 250V (quick acting)
Temperature Measurement
1. Set the Function switch to
O
C position and the LCD display will show ambient
temperature.
2. Insert the ‘K’ type thermocouple into the TEMP socket and contact the object
to be maesured with the thermocouple probe. Read the display.
WARNING. To avoid an electric shock, ensure the therrmocouple has been
removed before changing to another function.
Frequency Measurement
1. Connect the BLACK test lead to the COM jack and the RED test lead to
the V
Ω
Hz jack
2. Set the Function switch to 20kHz and connect test leads across the source or
load under measurement.
NOTE:
1. Reading is possible above 10V rms, but accuracy is not guaranteed.
2. in a noisy environment, it is preferable to use shielded cable to measure small
signals.
