manualshive.com logo in svg

Clarke CBS190B, Инструкция по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Clarke CBS190B Скачать руководство пользователя страница 19

19

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

TROUBLESHOOTING

Problem

Check

Solution

The unit fails to 
operate.

1. Check for power failure if
    the unit is plugged in.
2. Check the switch is on and
    that the fuse is not blown.
3. Door interlock switch not
    engaged.

1. Plug the unit into the
    socket.
2. Switch on or replace
     fuse.
3. Check that upper/lower
    doors are fully closed.

Blade breaks.

1. Faulty alignment (tracking).

2. Blade guides incorrectly
    adjusted.
3. Feeding the work too fast.
4. Forcing or twisting the blade
    around a tight radius.

5. Blade too tight.
6. Blunt teeth.
7. Blade is badly welded or
    brazed.
8. Wrong blade fitted.

9. Bandsaw left running when
    not in use.

1. Carry out tracking
    adjustments (p13).
2. Readjust blade guides
    (p14/15).
3. Lower the feed rate.
4. For tight curves, make
    relief cuts fairly close 
    together at 90º to the
    curve. A narrower blade
    will make a tighter
    curve.
5. Relieve blade tension.
6. Renew blade.
7. Renew blade.

8. Fit only quality blades
    supplied by your Clarke
    dealer.
9. Always switch machine
    off when not in use.

Noise or vibration. 1. Blade not correctly aligned.

2. Guides not securely set.

1. Carry out tracking
    adjustments (p13).
2. Tighten the locking
     knob. Check guides are
     correctly set.

Blade runs off the 
cutting line.

1. Blade guides incorrectly
    adjusted.
2. Blade tracking mal-adjusted
3. Blade tension too slack.
4. Wrong blade fitted (too
    thin).

1. Re-adjust blade guides.

2. Carry out tracking.
    adjustment (p13).
3. Re-tension blade.
4. Fit correct blade.

Содержание CBS190B

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды