Clarke CAT52 Скачать руководство пользователя

Страница: 7 / 16

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

BEFORE USE

NOTE:

Ensure the compressor is turned off.

1. Remove the blanking plug from the air inlet of the tool.

2. If required, connect an in-line mini oiler to the tool.

• A mini oiler helps to prolong the life of the air tool.

3. If a mini-oiler is not being used, run

a few drops of oil through the tool
before use. It can be entered
through the air inlet or via the hose
at the nearest connection to the
air supply.

4. Connect a suitable hose to the air

inlet as shown.

5. Connect the other end of the hose

to the compressor.

6. Your air tool is now ready for use.

You can fit a whip hose with a quick fit coupling if required (available from
your Clarke dealer).

FITTING THE SIDE HANDLE

1. Screw the side handle to the main

body as shown.

WARNING: COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU
ARE FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF AIR
COMPRESSORS AND COMPRESSED AIR SUPPLY.

Содержание CAT52

















Результаты поиска

Содержание CAT52

Отзывы:

Похожие инструкции для CAT52

Бренды по названию

Популярные бренды

Clarke CAT52, Инструкция по эксплуатации и обслуживанию

Результаты поиска

Содержание CAT52

Отзывы:

Похожие инструкции для CAT52

Бренды по названию

Популярные бренды