Clarke CAT220 3110474 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 16

background image

6

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

COMPRESSED AIR REQUIREMENTS

• A typical air line layout is shown below. If an automatic in-line filter/

regulator is used, it will keep the tool in good condition, but should
be regularly checked and topped up with oil. SAE 10 oil should be
used, and the lubricator adjusted to approx 2 drops per minute.

WARNING: COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU
ARE FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF AIR
COMPRESSORS AND COMPRESSED AIR SUPPLIES.

«
...
4
5
6
7
8
...
»

Содержание CAT220 3110474

















Отзывы:

Нет отзывов

Похожие инструкции для CAT220 3110474

Бренд: Stanford Страницы: 32

Бренд: RED ROOSTER Страницы: 8

GRASSHOPPER 2.0

Бренд: APEX Customs Страницы: 2

Бренд: Berner Страницы: 9

Бренд: Higo Страницы: 23

Бренд: Sioux Tools Страницы: 18

Бренд: Skil Страницы: 9

Бренд: Vector Страницы: 4

Бренд: Rupes Страницы: 10

Бренд: Power Craft Страницы: 20

Бренд: ULTIMATE SPEED Страницы: 66

Бренд: ULTIMATE SPEED Страницы: 78

Бренд: Raider Страницы: 52

MultiPrep System 15-2000-GI

Бренд: Allied Страницы: 44

Бренд: Ozito Страницы: 12

Бренд: Bar Maid Страницы: 4

Бренд: Pattfield Ergo Tools Страницы: 90

Бренд: Bosch Страницы: 123

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды