Clarke 7330375 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 32

Clarke 7330375 Скачать руководство пользователя страница 18

18

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

APPLYING DETERGENTS AND CLEANING SOLVENTS

1. Push the detergent hose onto the

ribbed fitting as shown.

2. Place the other end of the

detergent hose with the filter on it,
into a container holding the
chemical/cleaning solution.

3. Slide the nozzle forward for low

pressure operation.

NOTE:

See page 30 for detergent
and cleaning products available from your CLARKE dealer.

SHUTTING DOWN

1. After each use, if you have applied detergents, place the detergent hose

into a container of clean water and run clean water through the detergent
injection system to flush the system thoroughly.

NOTE:

Failure to do so could cause damage to the pump.

2. Method 1: Turn the ignition switch

to ‘OFF’, then close the fuel valve.

3. Method 2: Close the fuel valve

and wait for the engine to stop.

4. Turn the water supply off.

5. Pull the trigger on the spray gun to

release any water pressure.

6. See storage section in this manual

for proper storage procedures.

NOTE: NEVER

turn the water off with the engine running.

«
...
16
17
18
19
20
...
»

Содержание 7330375

































Отзывы:

Нет отзывов