manualshive.com logo in svg

Clarke 6485067, Инструкция по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Clarke 6485067 Скачать руководство пользователя страница 11

11

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

TORQUE ADJUSTMENT

To select the correct torque setting for screwdriving:

1. Set the mode selector to 1. 

2. Fit and tighten the first screw, 

3. if the clutch starts to ratchet 

before the screw is correctly 
seated, rotate the mode selector 
to a higher number until the 
clutch ratchets only when the 
head of the screw is flush with the 
surface of the material.

OPERATING THE DRILL

1. Make sure that the forward/reverse switch is positioned in either the 

forward, or reverse position. See page 9.

NOTE:

The trigger will not operate if the direction control switch is in the 
central position.

2. Squeeze the trigger.

• The drill will start.

• The speed can be increased by increasing the pressure on the 

trigger up to the maximum speed (Setting 1 - 350 rpm, Setting 2 - 
1250 rpm).

3. Release the trigger to stop the drill.

• The drill is fitted with an electric brake which stops the motor when 

the trigger is released.

CAUTION: DO NOT ADJUST THE MODE SELECTOR WHILE THE CHUCK IS 
ROTATING.

CON18NI.fm  Page 11  Tuesday, August 21, 2012  11:53 AM

Содержание 6485067

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды