Clarke 3110432 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 20

Clarke 3110432 Скачать руководство пользователя страница 14

14

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

2. Be aware that outside factors may effect the wrench’s operation and

efficiency, These may include reduced compressor output, excessive drain
on the airline, moisture in suspension or restrictions in the line, or the use of
connectors of improper size or poor condition which will reduce air supply.

3. Any major servicing and repairs should be carried out by your local CLARKE

dealer or a qualified service technician.

4. If the tool runs erratically or becomes inefficient, and the air supply is of

good quality, it may be necessary to dismantle the air motor and hammer
mechanism and replace worn or damaged parts. You may prefer to take
the tool to your CLARKE dealer if internal maintenance is required.

5. Your Clarke air tool has been designed to give long and trouble free

service. If, however, having followed the instructions in this booklet
carefully, you encounter problems, take the unit to your local Clarke
dealer.

STORAGE

1. If the tool is to be stored, or is idle for longer than 24 hours, run a few drops

of Clarke air line oil into the air inlet, and run the tool for 5 seconds in order
to lubricate the internal parts.

2. When not in use, disconnect from air supply, clean tools and store in the

moulded case provided. When storing, ensure the blanking plug is
replaced on the airline connector once the airline is disconnected.

**Clarke Airline Oil is available from your CLARKE dealer: Part No. 3050825.

ACCESSORIES

A wide range of airline accessories is available from your nearest CLARKE
dealer, for further information, contact your nearest dealer, or telephone
CLARKE International Sales Department on 01992 565300.

Suitable air line accessories include air filter/regulators, lubricators, hoses, snap
couplings, clips, gauges, valves.

Suitable Impact Wrench compatible socket sets include the following:

3110437

CAT37B

1 piece 1/2”square drive (metric)

1800310

CIS12/17

17 piece 1/2”square drive (metric/AF)

1800305

CIS9/32

32 piece 3/8” & 1/2”square drive (metric/AF)

1800345

CIS12/7M

7 piece 1/2”square drive universal joint (metric)

1800350

CIS12/7MD

7 piece 1/2”square drive universal joint (deep) metric

1800355

CIS12/6H

6 piece 1/2”square drive hex key set (metric)

1800360

CIS12/6S

7 piece 1/2”square drive TRX-Star

«
...
12
13
14
15
16
...
»

Содержание 3110432





















Отзывы:

Нет отзывов