Clarke 3110320 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 16

Clarke 3110320 Скачать руководство пользователя страница 2

2

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

INTRODUCTION

Thank you for purchasing this CLARKE Airbrush kit.

Before attempting to use this product, please read this manual thoroughly and
follow the instructions carefully. In doing so you will ensure the safety of yourself
and that of others around you, and you can look forward to your purchase
giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.

Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.

This guarantee does not effect your statutory rights.

SPECIFICATION

Paint jar capacity

22 cc

Metal paint cup capacity

5 cc

Connecting hose

4 mm dia x 1550 mm length

Airline connector size

1/4” bsp

Minimum airline hose size

3/8” (10mm)

Recommended operating pressure

29 psi/2bar (min15psi/max 50psi

Average air consumption

0.2 cfm

«
1
2
3
4
...
»

Содержание 3110320

















Отзывы:

Нет отзывов