background image

11

Parts & Service: 0871 410 1270 / e-mail: [email protected] or [email protected]

MAINTENANCE 

DRAIN THE RESERVOIR

After use, always open the drain valve to make sure that any condensate is 
drained off.

CHECK THE OIL 

Ensure the oil level is between the min and max marks on the dipstick. See 
“Check the Oil level” on page 6 and top-up if necessary - (use ISO100 (SAE30) 
compressor oil, available from your Machine Mart dealer).

CLEAN THE AIR FILTER

The air filter must be examined monthly and more often in dusty conditions,

1. Remove the securing bolt and pull 

the filter from the compressor.

2. Unclip the front and rear of the 

filter and pull out the filter 
element.

3. Clean the filter using a soft brush.

• If necessary, the filter can be 

carefully cleaned in warm 
soapy water.

• Rinse and let the filter dry 

completely before refitting.

• If the filter or filter element is damaged, you must replace it.

4. Reassemble the filter and refit it to the compressor using the securing bolt.

WARNING: MAKE SURE THAT THE COMPRESSOR IS DISCONNECTED FROM 
THE ELECTRICAL SUPPLY BEFORE CARRYING OUT ANY MAINTENANCE

Содержание 2245308





















Отзывы: