Clarke 2092500 Скачать руководство пользователя страница 11

Страница: 11 / 16

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

TROUBLESHOOTING CHART

IMPORTANT

1. Any remedial work that may be required must be carried out by a qualified

electrician/engineer.

2. Empty Air Receiver of Air before dismantling any part of the compressor

unit’s pressure system.

3. If your compressor develops a fault do not use until the fault has been

rectified.

SYMPTOM

PROBABLE CAUSE

REMEDY

Engine
difficult to
start

Load Genie leaking
(compressor unit is on load
during start).

Stop engine and empty air
receiver. Clean or replace
Load Genie

Load Genie valve blocked,
possibly frozen up.

Thaw Load Genie out (Unit
must be installed in frost-
free place).

Compressor
unit
constantly ‘on
load’

Load Genie defective

Have Load Genie serviced
or replaced

Load Genie set at a pressure
higher than the safety valve’s
opening pressure

Contact Clarke Service
Department

Load Genie leaking.

Contact Clarke Service
Department

Unusual noise
from
compressor.

Bolts loose.

Tighten bolts

Flywheel loose.

Tighten flywheel

Unit installed on an unsuitable
base.

Move unit to a more solid
base

Bearings, piston rings or
cylinder worn.

Contact Clarke Service
Department

Valve broken

Contact Clarke Service
Department

Содержание 2092500

















Результаты поиска

Содержание 2092500

Отзывы:

Похожие инструкции для 2092500

Бренды по названию

Популярные бренды

Clarke 2092500, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание 2092500

Отзывы:

Похожие инструкции для 2092500

Бренды по названию

Популярные бренды