Illuminators are powered by Power over the Ethernet (PoE) via a network cable
connector to a PoE IEEE802at compliant switch.
The power consumption of the illuminators comply with PoE IEEE802at.
These illuminators are not supplied with a power cord. Instead, they are supplied with a
1m long network cable. At the end of the network cable is a female RJ45 Cat5e compliant
connector with an IP68 rated cover.
The IP68 rated cover is supplied with the illuminator. Follow the instructions supplied with
the connector on how to attached if to the male Cat5e network cable.
ENSURE THAT THE IP68 RATED COVER IS CORRECTLY FITTED AND ATTACHED
TO THE NETWORK CABLE. IF THIS IS NOT FITTED CORRECTLY MOISTURE CAN
GET INTO THE CONNECTOR AND MAY CAUSE THE UNIT TO MALFUNCTION. THIS
WOULD VOID THE WARRANTY ON THE PRODUCT.
Recommended PSU
Any IEEE802.3at compliant switch or injector.
Power supply should be approved to relevant EN Safety standards.
Power Supply should be used with devices to protect against short circuits and overload.
External circuits used for interfacing with the illuminator (Camera Day/Night switching
and Telemetry) should be reinforced/double insulated from mains.
This product complies with the European Directive 2014/30/EU Electromagnetic
Compatibility and 2014/35/EU Low Voltage Directive by meeting the following standards:
This symbol on the product means that the electrical and/or electronic equipment
to which it relates should be disposed of at the end of life separately from domestic
household waste.
There are separate collection systems for recycling in the EU. For more information
please contact the Local Authority or supplier of the product
.
Photocell
The photocell is designed to automatically switch the lamps on at dusk and turn off at
dawn. A high degree of hysteresis is incorporated to void on/off switching in marginal
conditions. The unit is factory set at approximately 30 Lux On and 70 Lux Off, but can be
adjusted.
Trouble Shooting
Ensure all tests are undertaken by a qualified, trained engineer and ensure safe working
practices are followed at all times.
Step 1: Basics
•
Check power connection
•
Ensure PoE+ specification
•
Check the photocell is working - cover photocell ,light should turn on
•
Ensure power supply is suitably rated to product - check the specifications
Step 2: Set up Camera, lens and Illumination
•
Check alignment of lamp
•
Check camera lens- fully open at night and set correctly
•
Check model number to performance specification to ensure required distance is
achievable
Step 3: Call for further assistance
If the lamp is still not delivering the required performance, please contact Technical
Support for further assistance
Note down:
•
Model number and serial number of illuminator
•
Camera make and model
•
Lens make and model
Safety Warning
•
When the lamp is running, it is hot to touch. before touching switch off the illuminator
and allow to cool for a minimum of 10 minutes.
•
The illuminator should be positioned so that prolonged starring into the illuminator at a
distance closed than 1m is not expected.
•
The light source of this illuminator is not replaceable, when the light source reaches its
end of life the whole illuminator should be replaced.
•
If the flexible power cord of the illuminator is damaged it should be exclusively replaced
by an authorised service agent.
•
This equipment is not suitable for use in locations where children are likely to be
Factory Default Settings
When using the system for the first time, or if a factory reset has been made, the follow-
ing settings are used.
Product IP number:
192.168.0.10
Subnet mask:
255.255.255.0
Default router:
192.168.0.1
Login
1. Open a web browser.
2. In the address field, type in the selected unit IP-address.
3. The user interface login page is shown.
4. Create your username and password.
User manual can be downloaded from our website at
www.gjd.co.uk
Pressure relief valve
IM Ethernet cable with
IP68 connector
LED indicator
Reset
CE-EMC
EN55032
EN55024
EN 61547
EN 55015
EN 62493
EN 50130-4
(IT Immunity)
(IT Immunity)
(Lighting-Immunity)
(Lighting-Emission)
(Lighting -EMF)
(Alarm-EMC)
CE-LVD
EN 60598-1
EN 60598-2-1
(Luminaires-General)
(Luminaires)
Safety
EN 62471 Risk
group 2
(LED safety)
Environmental
IEC/EN 60529
EN50130-5
IP66
(Alarm-environmental)
USA
FCC, Class B
AUS
RCM (AS/NZS CISPR 22 Class B)
RoHS:
Restriction of Hazardous Substances European directive
202/95/EC
Certifications
WEEE:
Waste Electrical & Electronic Equipment European directive
202/96/EC
POWER AND CONTROL CABLE CONNECTIONS
CLARIUS IP
CERTIFICATIONS
