26
DO NOT DIVE.
100
DO NOT DIVE.
TWILIGHT SPA – CONTROLS
TS 6.2 • TS 67.25 • TS 7.2 • TS 7.25 • TS 8.2 TS 8.25 • TS 8.3 TS 8.35 • TS 240
InItIal Start-up
When your spa is first actuated, it will go into Priming mode, indicated by “
” Be sure the
pumps and heating system are free of air by cycling the pumps on and off with the spa-side panel
buttons. The spa will not heat during priming mode, allowing time to verify all air is purged from
the heater. The Priming mode will last for less than 5 minutes (press “Warm” or “Cool” to skip
Priming Mode) and then the spa will begin to heat and maintain the water temperature in the
Standard mode.
Warm/Cool (80°F - 104°F / 26°C - 40°C)
The start-up temperature is set at 100F°/37°C. The last measured temperature is constantly dis-
played on the LCD.
Note that the last measured spa temperature displayed is current only when the low speed of
pump 1 has been running for at least 2 minutes (temperature is always current on spas equipped
with 24 hour circulation pump). To display the set temperature, press the “Warm” or “Cool” pad
once. To change the set temperature, press the pad a second time before the LCD stops flashing.
Each press of the “Warm” or “Cool” pad will continue to either raise or lower the set tempera-
ture. After three seconds, the LCD will stop flashing and display the current spa temperature.
Jets 1
Touch the “Jets” button once to turn pump 1 on or off, and to shift between low and high
speeds. If left running, the low speed of the pump will automatically turn off after 4 hours, and
the high speed will automatically turn off after 15 minutes.
Jets 2
Touch the second “Jets” button once to turn pump 2 on or off. If left running, pump 2 will auto-
matically turn off after 15 minutes. This pump has one speed.
Jets 3 (If so equipped)
Touch the second “Jets” button once to turn pump 2 on or off. If left running, pump 3 will auto-
matically turn off after 15 minutes This pump has one speed.
controls
100
DO NOT DIVE.
TWILIGHT SPA – CONTROLS
TS 6.2 • TS 67.25 • TS 7.2 • TS 7.25 • TS 8.2 TS 8.25 • TS 8.3 TS 8.35 • TS 240
InItIal Start-up
When your spa is first actuated, it will go into Priming mode, indicated by “
” Be sure the
pumps and heating system are free of air by cycling the pumps on and off with the spa-side panel
buttons. The spa will not heat during priming mode, allowing time to verify all air is purged from
the heater. The Priming mode will last for less than 5 minutes (press “Warm” or “Cool” to skip
Priming Mode) and then the spa will begin to heat and maintain the water temperature in the
Standard mode.
Warm/Cool (80°F - 104°F / 26°C - 40°C)
The start-up temperature is set at 100F°/37°C. The last measured temperature is constantly dis-
played on the LCD.
Note that the last measured spa temperature displayed is current only when the low speed of
pump 1 has been running for at least 2 minutes (temperature is always current on spas equipped
with 24 hour circulation pump). To display the set temperature, press the “Warm” or “Cool” pad
once. To change the set temperature, press the pad a second time before the LCD stops flashing.
Each press of the “Warm” or “Cool” pad will continue to either raise or lower the set tempera-
ture. After three seconds, the LCD will stop flashing and display the current spa temperature.
Jets 1
Touch the “Jets” button once to turn pump 1 on or off, and to shift between low and high
speeds. If left running, the low speed of the pump will automatically turn off after 4 hours, and
the high speed will automatically turn off after 15 minutes.
Jets 2
Touch the second “Jets” button once to turn pump 2 on or off. If left running, pump 2 will auto-
matically turn off after 15 minutes. This pump has one speed.
Jets 3 (If so equipped)
Touch the second “Jets” button once to turn pump 2 on or off. If left running, pump 3 will auto-
matically turn off after 15 minutes This pump has one speed.
