Clarion XC7420 Скачать руководство пользователя страница 8

8

ENGLISH

Power Connections

Your XC7-Series amplifi er can only produce power if it is fed power effi ciently. Clarion 
recommends the use of minimum of 4 AWG copper wire for all power and ground 
connections. The use of undersized power wiring may result in damage to your amplifi er.

Clarion also recommends performing “The Big Three” upgrade to your electrical system 
when any high power amplifi er is being installed. This includes upgrading the power wire 
between your battery and the alternator for both positive and ground connections, as 
well as the ground connection between the battery and the chassis and/or rear ground 
location.

The amplifi er ground connection is the most important connection in terms of reliable and 
effi cient operation of your amplifi er. This connection should be made to a solid and secure 
point on the vehicle chassis, or directly to the battery. Do not use a seat or seatbelt bolt 
as a ground location. All of the sound deadening, paint and primer must be removed from 
the chosen ground location. The ground ring terminal(s) should be secured with a bolt and 
locking fastener.
NOTE: Many new vehicles are assembled with extensive aluminum materials, composites 
and high strength adhesives. Clarion recommends running a ground wire of the same size 
as the power wire from the negative terminal of your battery to the ground location of your 
amplifi er. This is known as a parallel ground.

Wiring Precautions

Read all of the wiring precautions prior to making any connections. If you are unsure and/
or don’t have the necessary installation hardware, contact your local Clarion dealer to 
perform the installation.

1.  Before you begin the installation, make sure the vehicle is not running and is in the 

OFF position.

2.  Disconnect the negative (-) lead of the battery (or batteries) before making any power 

connections.

3.  When making connections, be sure that each connection is clean and secure.

4.  Insulate connections with split loom or heat shrink tubing where possible.

5.  A fuse holder and fuse must be installed on the lead coming from the positive (+) 

terminal of the battery. This fuse should located as close a possible to the battery 
terminal for maximum protection. Clarion does not recommend the use of a circuit 
breaker as a protection device.

6.  The battery fuse rating should equal the total current consumption at full output of the 

amplifi er(s) connected to that wire. Do not install the fuse until the entire installation 
has been completed.

+12V

GND

REM

Battery

+

-

Fuse

Blue/White

Parallel Ground

Battery

Ground

Chassis

Ground

Содержание XC7420

















Отзывы: