English
6
CZ202E/CZ202ER/CZ202EG
Audio Setup
Select tuner as playing source
Press [
SRC /
] button once or more to enter
RADIO
mode.
Select the radio band
Press the [
BAND
] button on the panel to select
one radio band among FM1, FM2, FM3, MW
and LW.
Manual tuning
During manual tuning, the frequency will be
changed in steps.
Press the [
] / [
] buttons on the panel
to select a higher / lower station.
Auto tuning
Press and hold the [
] / [
] buttons on
the panel to seek a higher / lower station.
To stop searching, repeat the operation above
or press other buttons having radio functions.
Note:
When a station is received, searching stops and
the station is played.
Preset scan
Preset scan receives the stations stored in
preset memory in order. This function is useful
when searching for a desired station in memory.
Radio Operations
Radio Operations
1. Press the [
PS/AS
] button.
2. When a desired station is tuned in,
press the [
PS/AS
] button again to
continue receiving that station.
Note:
•
Be careful not to press and hold the
[
PS/AS
] button for 1 second or longer,
otherwise the auto store function will
begin and the unit starts storing stations.
Auto store
Only stations with sufficient signal strength
will be detected and stored in the memory.
Press and hold the [
PS/AS
] button (1 sec.)
to start automatic station search.
To stop auto store, press other buttons
having radio functions.
Notes:
1. After auto store, the previous stored
stations will be overwritten.
2. The unit has 5 bands, such as FM1,
FM2, FM3, MW, LW. FM3 and MW, LW
can store by AS function. Each bands
can store 6 stations, CZ202E/CZ202ER/
CZ202EG can store 30 stations in total.
-> MID-G -> MID-F -> MID-Q -> TRE-G ->
TRE-F, rotate the [
VOLUME
] knob to select a
value.
BAS-G / MID-G / TRE-G: (-7)- (+7)
BAS-F: 60 / 80 / 100 / 200
BAS-Q: 1.0 / 1.25 / 1.5 / 2.0
MID-F: 500 / 1K / 1.5K / 2.5K
MID-Q: 0.5 / 0.75 / 1.00 / 1.25
TRE-F: 10.0K / 12.5K / 15.0K / 17.5K
Press the [ ]
button, then press
[
]
or [
]
] buttons to select USER preset
including:
BALANCE -> FADER -> M-B EX -> LPF(low
pass filter) -> S-W VOL (Subwoofer Volume),
rotate the [
VOLUME
] knob to select a value.
BALANCE:LEFT 1-7->CENTER->RIGHT 1-7
FADER:FRONT 1-7->CENTER->REAR 1-7
M-BEX: ON/OFF
LPF: THROUGH/80/120/160
SUBW VOL: (-6)-(+6)
Manual store
When one expected radio station has been
detected, press and hold number button 1-6 to
store it in the memory.
Recall the stored stations
Press one numeric button among 1 to 6 on the
panel to select the corresponding stored station.
Local seeking
When LOCAL seeking is ON, only those radio
stations with strong radio signal could be
received.
To select LOCAL function, press and hold
the [
DISP
] button on the front panel, then
press [
] button repeatedly until
LO or
DX
displays on the screen, and rotate the
[
VOLUME
] knob to select Local or Distant
mode.
Note:
The number of radio stations that can be
received will decrease after the local seeking
mode is ON.
Radio Data System Operations
Radio Data System
This unit has a built-in “Radio Data System”
decoder system that supports broadcast stations
transmitting “Radio Data System” data.
When using the “Radio Data System” function,
always set the radio to FM mode.
AF function
The AF function switches to a different
frequency on the same network in order to
maintain optimum reception.
* The factory default setting is ON.
1. Set to system setup by long pressing [
DISP]
button.
2. Press the [
] or [
] button to select
“
AF
”.
3. Rotate the [
VOLUME
] knob to select ON or
OFF.
• AF ON:
“
AF
” indicator appears in the display and AF
function turns on.
• AF OFF:
“
AF
” indicator disappears in the display and
AF function turns off.
REG (Regional programme)
function
When the REG function is ON, the optimum
regional station can be received. When this
function is OFF, if the regional station area
switches as you drive, a regional station for
that region is received.
* The factory default setting is ON.
Notes:
• This function is disabled when a national
station such as BBC R2 is being
received.
• The REG function ON/OFF setting is
valid when the AF function is ON.
1. Set to system setup by long pressing
[
DISP
] button.
2. Press the [
] or [
] button to
select “
REG
”.
3. Rotate the [
VOLUME
] knob to select ON
or OFF.
Содержание CZ202E
Страница 1: ...CZ202E CZ202ER CZ202EG ...
