English
7
CMD8
Handling Discs
Handling
• New discs may have some roughness
around the edges. If such discs are used,
the player may not work or the sound may
skip. Use a ball-point pen or the like to
remove any roughness from the edge of
the disc.
• Never stick labels on the surface of the disc
or mark the surface with a pencil or pen.
• Never play a disc with any cellophane tape
or other glue on it or with peeling off marks.
If you try to play such a disc, you may not
be able to get it back out of the player or it
may damage the player.
• Do not use discs that have large scratches,
are misshapen, cracked, etc.
Use of such discs may cause misoperation
or damage.
• To remove a disc from its storage case,
press down on the center of the case and
lift the disc out, holding it carefully by the
edges.
• Do not use commercially available disc
protection sheets or discs equipped with
stabilizers, etc. These may damage the
disc or cause breakdown of the internal
mechanism.
Storage
• Do not expose discs to direct sunlight or
any heat source.
• Do not expose discs to excess humidity or
dust.
• Do not expose discs to direct heat from
heaters.
Cleaning
• To remove fingermarks and dust, use a soft
cloth and wipe in a straight line from the
center of the disc to the circumference.
• Do not use any solvents, such as
commercially available cleaners, anti-static
spray, or thinner to clean discs.
• After using special disc cleaner, let the disc
dry off well before playing it.
On Discs
• Never turn off the power and remove the
unit from the boat with a disc loaded.
CAUTION
For your safety, the driver should not insert
or eject a disc while driving.
Ball-point pen
Roughness
4. CAUTIONS ON HANDLING
5. OPERATIONS
Basic Operations
Note:
• Refer to the diagrams in “3. CONTROLS”
when reading this chapter.
CAUTION
When the unit is turned on, starting and
stopping the engine with its volume raised to
the maximum level may harm your hearing.
Be careful about adjusting the volume.
Power on / off
Notes:
• Start the engine before using this unit.
• Be careful about using this unit for a long
time without running the engine. If you
drain the battery too far, you may not be
able to start the engine and this can reduce
the service life of the battery.
1. Start the engine. The power button / knob
illumination on the unit will light up.
Engine ON
position
2. Press the [
POWER /
] button on the front
panel or the [
SRC /
] remote control to
turn on the power under standby mode.
The unit goes back to the last status after
power on.
3. Press and hold the [
POWER /
] button
on the front panel or the [
SRC /
] remote
control to turn off the power.
Mute
Press the [
MUTE
] button on the remote control
to mute the volume from the unit.
Note
:
Doing the operation above again or adjusting
volume will release muting.
Volume adjustment
Rotate the [
VOLUME
] knob on the front panel
or press the [
] or [
] button on the remote
control.
The adjustable range of volume is 0 to 40.
CAUTION
While driving, keep the volume level at
which external sounds can still be heard.
Playing source selection
Press the [
DISC
], [
AUX/iPod
], [
AM/FM] or
[SAT
] button to change the operation mode.
* iPod or iPhone can connect to this unit via
CCA-750 cable.
Display system time
Press the [
DISPLAY
] button on the front
panel or the [
DISP
] remote control to switch
the display information from clock, station
information (radio mode), or track information
(CD mode).
RESET
If you have following problems, please press
[RESET
] button.
• Unit can not power on
• Nothing happens when buttons are pressed
• Display is not accurate
Note:
* When the [
RESET
] button is pressed, preset
radio stations, audio setting, etc.stored in
memory are retained.
RESET
