Claas RU 450, Руководство по ремонту

Страница: 3 / 31

297 925.0 - RU 450
I / 1
Contens
1. General information
Introduction .......................................................................... 1.1 / 1
Introduction to the CLAAS Repair Manual ........................... 1.2 / 1
Especially important ............................................................. 1.2 / 1
Identification plate .......................................................... 1.2 / 1
General information for repairs ............................................ 1.2 / 1
Explanation of the picture symbols ...................................... 1.2 / 4
Safety ................................................................................... 1.3 / 1
Identification of warning and danger notices ................. 1.3 / 1
Important operation information ........................................... 1.3 / 1
Hydraulic equipment ...................................................... 1.3 / 2
Screws ........................................................................... 1.3 / 2
Technical data .................................................................... 1.4 / 1
Oil filling capacity for the gearbox .................................. 1.4 / 2
Machine overview RU 450 ................................................... 1.5 / 2
2. Auger trough
Auger trough ....................................................................... 2.1 / 1
Removing/putting on the left and right protection cover 2.1 / 1
Removing/putting on the crop guard and tube carrier ... 2.1 / 1
Removing/putting on middle crop guard and crop tube . 2.1 / 2
Replacing the feeder segments ..................................... 2.1 / 2
Replacing the middle inner feeder segment .................. 2.1 / 2
Replacing the feed shear bar. ....................................... 2.1 / 3
Changing and installing the guide plates ....................... 2.1 / 3
Replacing the feed plates .............................................. 2.1 / 3
Replacing the scrapers .................................................. 2.1 / 5
3. Machine frame
Removing/putting on the lock ........................................ 3.1 / 1
Removing/putting on left and right side of the supporting arm .
3.1 / 2
Installing the rotor transmission ..................................... 3.1 / 4
Putting in the angular transmission with the tapered clutch. .....
3.1 / 6
Replacing the tapered clutch ......................................... 3.1 / 7
Removing the supporting arm ....................................... 3.1 / 9
Installing the supporting arm ....................................... 3.1 / 11
4. Knife/Feed
Intermediate points .............................................................. 4.1 / 1
Removing/installing the intermediate points .................. 4.1 / 1
Removing/installing the support to the intermediate points. .....
4.1 / 1
Removing/putting on the sliding skid ............................. 4.1 / 1
Removing/putting on the position transmitter ................ 4.1 / 2
Removing/putting on the divider points ......................... 4.1 / 2
Removing/putting on the outer points ............................ 4.1 / 3
Removing/installing the intake plates ................................... 4.2 / 1
Removing/installing the left or right intake plates .......... 4.2 / 1
Removing/putting on the upper intake plates ................ 4.2 / 7
Removing/putting on the bottom intake plates .............. 4.2 / 8
Removing/installing the cutting disks ................................... 4.3 / 1
Replacing the knife on the cutting disks ........................ 4.3 / 1
Removing the cutting disks ............................................ 4.3 / 2
Installing the cutting disks .............................................. 4.3 / 3
Intake taper ......................................................................... 4.4 / 1
Removing the intake taper ............................................ 4.4 / 2
Replacing the overload clutch ....................................... 4.4 / 3
Removing/putting on the outside chamber bottom. ....... 4.4 / 3
Installing the intake taper .............................................. 4.4 / 4
5. Hydraulic
Hydraulic ............................................................................. 5.1 / 1
Removing the hydraulic cylinder ................................... 5.1 / 1
Taking apart the hydraulic cylinder ............................... 5.1 / 2
Putting the cylinder back together ................................. 5.1 / 5
Installing the hydraulic cylinder ..................................... 5.1 / 8
6. Special equipment
Removing/putting on the safety covers ............................... 6.1 / 1
Removing/putting on the guard rails ............................. 6.1 / 1
Removing/putting on the guard plate ............................ 6.1 / 1
Removing/putting on the protective covering ................ 6.1 / 2
Removing/putting on the left and right guard plate ....... 6.1 / 4
Removing/putting on the cover ..................................... 6.1 / 4
Lodged corn auger .............................................................. 6.2 / 1
Taking off the lodged corn auger .................................. 6.2 / 1
Installing the lodged corn auger .................................... 6.2 / 4
Autopilot .............................................................................. 6.3 / 1
Removing/putting on the sensor system ....................... 6.3 / 1
Removing/putting in the wiring harness ........................ 6.3 / 3
7. Drives
Auger drive .......................................................................... 7.1 / 1
Removing the auger drive ............................................. 7.1 / 1
Removing/putting on the bearing housing ..................... 7.1 / 4
Removing the feeder auger ........................................... 7.1 / 5
Putting in the feeder auger ............................................ 7.1 / 7
Installing the auger drive ............................................... 7.1 / 8
Replacing the comb feeders on the feeder trough ...... 7.1 / 12
Replacing the reinforcement on the feeder trough. ..... 7.1 / 13
Knife drive ........................................................................... 7.2 / 1
Removing/installing the entering transmission .............. 7.2 / 1
Removing/installing the main transmission ................... 7.2 / 2
Removing/installing the rotor transmission ................... 7.2 / 6
Bevel drive ........................................................................... 7.3 / 1
Removing/installing the bevel drive ............................... 7.3 / 1
Transmission ....................................................................... 7.4 / 1
General - Important information .................................... 7.4 / 1
Main transmission (B) .......................................................... 7.5 / 1
Taking apart the main transmission .............................. 7.5 / 1
Putting together the main transmission ......................... 7.5 / 9
Main transmission - Shift transmission (H) .......................... 7.6 / 1
Main transmission – Taking apart the shift transmission (H) ...
7.6 / 1
Main transmission – Putting together the shift transmission ....
7.6 / 15
Bevel transmission .............................................................. 7.7 / 1
Taking apart/putting together the bevel transmission ... 7.7 / 1
Putting together the bevel transmission ........................ 7.7 / 8
Rotor transmission .............................................................. 7.8 / 1
Taking apart the rotor transmission ............................... 7.8 / 1
Find manuals at http://best-manuals.com/search?&s=CLA-2979250