Claas LEXION 740 Скачать руководство пользователя страница 34

Страница: 34 / 60

Settings:

Separation Rotors

Approximately 70% of the grain needs to be separated from the straw by
the time the crop leaves the drum. This means that the remaining 30%
has to be separated by the rotors.

If the rotor speed is too fast, broken straw
and chaff is produced which could lead to
overloading of the sieves.

TIP.

Rotor speed changes should be

made at about 50rpm increments.

The straw will only travel along the rotor
at one speed. This will differ for every
crop, machine and condition.

Rotor cover plates can be opened or
closed during threshing. Both covers
should be open when maximum
separation is needed.

If fitted with 4D SEPARATION there
are now three sets of doors. They
can be operated in the same manner
as the standard rotor cover plates.

TIP.

In situations where the straw is

breaking up, it may be beneficial to
close either one, two or all three to
reduce sieve overloading problems.

TIP.

To find the correct speed, start

with the rotor speed at a high rpm
and then adjust the rotor speed till
the desired separation is achieved.

Содержание LEXION 740




























































Результаты поиска

Содержание LEXION 740

Отзывы:

Похожие инструкции для LEXION 740

Бренды по названию

Популярные бренды

Claas LEXION 740, Информация и базовые настройки поля

Результаты поиска

Содержание LEXION 740

Отзывы:

Похожие инструкции для LEXION 740

Бренды по названию

Популярные бренды