DMX Address is 001,CH04
DMX Address is 001,CH05
DMX Start Address-
Output Resolution-
PWM Frequency
Device DMX Proles
Dimming Curve
(Factory default is 001)
(Factory default is 16)
(Factory default is 01)
(Factory default is 1.1)
(Factory default is 1.5 )
08
or
16
00
thru
30
0.1
thru
9.9
DMX Channel Qty-
(Factory default is 05)
SETTINGS:
CH01
: DMX addresses 1,2,3,4,5 = 001
CH02
: DMX addresses, 1,3 =001, 2,4,5 =002
CH03
: DMX addresses, 1 =001, 2 =002, 3,4,5 =003
CH04
: DMX addresses, 1 =001, 2 =002, 3 =003,
4,5 =004
CH05
: DMX addresses, 1 =001, 2 =002, 3 =003,
4 =004, 5 =005
Values:
00 = 500Hz
01 to 30 = 1kHz to 30kHz
PWM frequency is used to tune the dimmer for
icker free operation when used with high speed
cameras. A high PWM value produces the least
amount of icker. A low PWM value produces
better dimming quality. Always perform a
camera test to conrm optimal results.
The Dimming Curve may be adjusted to
affect the rate of rise and fall of the dimmer.
Values less than 1.0 increase the rate, while
values greater than 1.0 decrease the rate.
(1.0 is linear)
Resolution determines the smoothness of the
dimming. 8 bit uses 1 DMX channel, while 16
bit uses 2.
Sets the DMX address for the dimmer.
AVAILABLE SETTINGS:
AVAILABLE SETTINGS:
AVAILABLE SETTINGS:
LIGHT
OUTPUT
DMX CONTROL SETTING
<1
>1
1.5
1.0
2.5
3.5
6.5
0.9
0.8
Channel 1
Channel 2
Channel 3
Channel 4
Channel 5
Channel 6
Channel 7
Channel 8
Channel 9
Channel 10
Channel 1
Channel 2
Channel 3
Channel 4
Channel 5
Channel 6
Channel 7
Channel 8
Channel 1
Channel 2
Channel 3
Channel 4
Channel 5
Channel 6
Channel 1
Channel 2
Channel 3
Channel 4
Channel 1
Channel 2
dp1.1
dp1.1
dp1.1
dp1.1
dp1.1
dp2.1
dp2.1
dp2.1
dp2.1
dp2.1
dp3.2
dp4.3
dp5.4
dp6.5
dp5.3
dp6.4
dp7.5
For output 1&3
dimming
For output 1
dimming
For output 1
dimming
For output 1
dimming
For output 1
dimming
For output 1
dimming
For output 1
dimming
For output 1
dimming
For output 2
dimming
For output 2
dimming
For output 2
dimming
For output 2
dimming
For output 3
dimming
For output 3
dimming
For output 3
dimming
For output 3
dimming
For output 3
dimming
For output 3
dimming
For output 5
dimming
For output 5
dimming
For output 5
dimming
For output 4&5
dimming
For output 4&5
dimming
For output 4&5
dimming
For output 2
dimming
For output 2
dimming
For output 2
dimming
For output 2
dimming
For output 4
dimming
For output 4
dimming
For output 4
dimming
For output 2
dimming
For output 1
dimming
For output 1
dimming
For output 2,4&5
dimming
For output 3,4&5
dimming
For output 3,4&5
dimming
For output 3,4&5
dimming
For output 2,4&5
dimming
For output 1&3
dimming
For all output
dimming
Strobe Effects
Strobe Effects
Strobe Effects
For all output
dimming
For all output
dimming
For all output
dimming
For all output
dimming
For all output
dimming
For all output
dimming
For all output
dimming
For all output
dimming
For output 1
dimming
For output 1
dimming
For output 4&5
dimming
For output 4&5
Fine dimming
For output 2
dimming
For output 2
dimming
For output 4
dimming
For output 3
dimming
For output 3
dimming
For output 5
dimming
For output 2
dimming
For output 1
dimming
For output 1
Fine dimming
For output 1
Fine dimming
For output 1
Fine dimming
For output 2
Fine dimming
For output 2
Fine dimming
For output 2
Fine dimming
For output 4
Fine dimming
For output 3
Fine dimming
For output 3
Fine dimming
For output 5
Fine dimming
For output 2,4&5
dimming
For output 3,4&5
dimming
For output 3,4&5
Fine dimming
For output 2,4&5
Fine dimming
For output 1&3
dimming
For output 1&3
Fine dimming
For all output
dimming
For all output
Fine dimming
Note*- To restore factory defaults, press and hold both
“Enter” and “Select” for 5 seconds until display goes out.
DMX Address is 001,CH01
DMX Address is 001,CH02
DMX Address is 001,CH03
©201
7
City Theatrical, Inc.
Rev 1.05
QolorFLEX 5x8A Dimmer
Choosing DMX Mode or Stand Alone Mode
Power up unit. Address screen will be showing (Axxx)
In DMX Mode (“run1”):
Axxx = DMX Address
CH0x = Quantity of channels controlled
Btxx = 8 or 16 bit dimming
PFxx = PWM frequency 00 to 30
gAxx = Dimming Curve 0.1 to 9.9
dPxx
= DMX Profi
les
ote: set DMX profile to
“2.1”
for 16 bit two channel di
mming)
Set
o Stand Alone Mode by pushing “Up” button until “run1” is shown.
“run1” denotes DMX mode. Hit “Enter” button, and “Up” button to select
“run2”, which denotes Stand Alone Mode.
Cycle power to unit
.
In Stand Alone Mode:
Run2 = Stand Alone Mode
Pxxx
= Programs 1 31
b xx
= Brightness levels 1 8
SPxx
= Speed levels 1 16
x xx
= Individual channels
vels
To change back to DMX Mode, select “run1” and cycle power
