<Elapsed Time Measurement>
(1) Press button
A
to start/stop Chronograph.
1 Each time you press button
A
while in time
measurement, start/stop is repeated.
2 EL light is turned ON for 3 seconds when
counting is stopped.
(2) Press button
B
when counting is stopped to
reset chronograph.
<Split Time Measurement>
(1) Press button
A
to start/stop Chronograph.
(2) Press button
B
while in time measurement.
Split time will appear for 10 seconds.
1 “SPL” will flash while split time is displayed.
2 EL light is turned on for 3 seconds at the time
of split time operation.
(3) Press button
B
when counting is stopped to
reset Chronograph.
• Timer can be set in units of 1 minute up to 60
minutes. When Timer countdown is finished,
buzzer will sound for about 5 seconds and return
to the Timer set time.
• When the tap switch is ON, tap the watch gently
to light the EL light.
<To Set Timer>
(1) If you press button
A
while the set time is
flashing in timer mode, the set time will be
reduced by one minute for each time you press
and release the button. Continue until you reach
the set time you want.
(Press and hold button
B
to make rapid
adjustment to the set time.)
<To Use Timer>
(1) Press button
A
. Timer starts countdown from
set time.
(2) Press button
A
to stop Timer during in the
measurement. Press button
A
to start it again
while in the “Stop” position.
• Press button
B
, while Timer is in operation, to
return to the initial set time, and start the
countdown again.
(3) If you press button
B
while Timer is stopped,
Timer will return to the initial set time.
• The confirmation tone will sound when you press
the button.
7. All Reset Function
Use All Reset function to reset the watch after
replacing the battery or if the watch is showing
abnormal operation or display. All Reset function
can be performed as follows:
(1) Pull crown out.
(2) Press buttons
A
,
B
and
M
simultaneously. (All
digital displays will disappear while pressing.)
(3) Release three buttons. (All digits are shown.)
(4) Push crown in. (At this point, buzzer sounds in
confirmation.)
This completes the All-Reset operation. Set
each mode correctly before using the watch.
8. Precautions
CAUTION Water-Resistance Performance
There are several types of water-resistant watches,
as shown in the following table. For correct use
within the design limits of the watch, confirm the
level of water-resistance of your watch, as indicated
on the dial and case, and consult the table.
• Water-resistance for daily use (to 3 atmospheres):
This type of watch is water-resistant to minor
exposure to water. For example, you may wear
the watch while washing your face; however, it is
not designed for use underwater.
• Upgraded water-resistance for daily use (to 5
atmospheres): This type of watch is water-
resistant to moderate exposure to water. You may
wear the watch while swimming; however, it is not
designed for use while skin diving.
• Upgraded water-resistance for daily use (to 10/20
atmospheres): This type of watch may be used for
skin diving; however, it is not designed for scuba
or saturated diving using helium gas.
If switched to another mode while Chronograph
is running and then returned to Chronograph
mode again, the watch will return to countdown
continuing at the time of switching. (If switched
while Split Time is shown, the watch will return
to Chronograph running mode.)
However, if Chronograph counting has exceeded
24 hours, the watch will return to initial
Chronograph reset display.
Timer Mode
E
Remaining Time
(Minutes, Seconds)
Timer Setting Time
If watch is switched to another mode while
Timer is in operation and then returned to
Timer mode again, the watch will return to
countdown continuing at the time of switching.
However, if countdown has completed, the
watch will return to initial Timer setting.
