Citizen CL-E700 Series Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 236

background image

Chapter 2 Operating Principles

2-3.

Operation Panel

2-59

CL-E700 series

(3)

How to change the settings in Factory mode

• In Factory mode, DO NOT change the factory-set values unless you need to

change them, since there are essential items related to printing accuracy, etc.

• Do not turn OFF the power of the printer until you finish the adjustment. If it is

turned OFF, you need to repeat the adjustment from the beginning.

• The value adjusted here is retained until you change it with the same

procedure. Note that, even if you perform initialization by selecting “Test
Mode” main menu, “Factory Default” submenu and “Yes” in that order, the
changed value here does not return to the initial value set at the factory.

(3-1) Submenu table in Factory mode

The following table shows the submenus of “Factory Setup” main menu.
For the factory submenu operation, refer to the next item “

(3-2) Setting submenu in Factory

*1 “[Factory Mode Settings Menu name]” in “Submenu Name” column shows the name

that will be printed in “Factory Mode Settings”. (Refer to “

2-3-3(2) How to print the

Factory Mode Settings menus

”.)

*2 “+” shows that the object moves forward/rightward electrically, while “-” shows that it

moves backward/leftward electrically. 8 dots correspond to 1 mm (203 dots correspond
to 1 inch).

Submenu Name

[Factory Mode Settings

Menu name]

Adjustable Value

(Default Value)

Description

Init Thru Sen

Performs calibration of the transparent sensor
sensitivity. For details, refer to “

3-7-1(2) Sensor

sensitivity adjustment (Factory mode)

Chapter 3.

Init Refl Sen

Performs calibration of the reflective sensor
sensitivity). For details, refer to “

3-7-1(2) Sensor

sensitivity adjustment (Factory mode)

Chapter 3.

Through Pos
[Through Sensor Position]

-256 to +256 dot
(+000 dot)

Electrically shifts the position of transparent
sensor back and forth.
(-32 to +32 mm, -1.26 to +1.26 inches)

Reflect Pos
[Reflect Sensor Position]

-256 to +256 dot
(+000 dot)

Electrically shifts the position of reflective sensor
back and forth.
(-32 to +32 mm, -1.26 to +1.26 inches)

Mach Tear Pos
[Machine Tear Position]

-256 to +256 dot
(+000 dot)

Electrically shifts the tear off position back and
forth. (-32 to +32 mm, -1.26 to +1.26 inches)

Mach Cut Pos
[Machine Cut Position]

-256 to +256dot
(+000 dot)

Electrically shifts the cut position back and forth.
(-32 to +32 mm, -1.26 to +1.26 inches)
(Option)

Mach Peel Pos
[Machine Peel Position]

-256 to +256dot
(+000 dot)

Electrically shifts the peel position back and
forth. (-32 to +32 mm, -1.26 to +1.26 inches)
(Option)

«
...
71
72
73
74
75
...
»

Содержание CL-E700 Series













































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CL-E700 Series

Бренд: TSC Страницы: 78

Бренд: Salto Страницы: 2

Бренд: Seypos Страницы: 69

Бренд: IDTECH Страницы: 37

Бренд: Motorola Страницы: 44

Бренд: QVSR Страницы: 4

OBID i-scan ID ISC.MR200-EP

Бренд: Feig Electronic Страницы: 53

Бренд: Worth Data Страницы: 2

PowerScan M8300

Бренд: Datalogic Страницы: 24

Бренд: Obreey Страницы: 54

Бренд: Sun Microsystems Страницы: 22

TWN4 Palon Compact LEGIC

Бренд: Elatec Страницы: 15

Бренд: ViewSonic Страницы: 2

FUNK MK-5120ZBe

Бренд: Albasca Страницы: 2

Бренд: Nordic ID Страницы: 20

CSN SMART AY-H6355BT

Бренд: Rosslare Страницы: 35

Бренд: MIWA LOCK Страницы: 9

Бренд: SICK Страницы: 166

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды