Citizen CL-E700 Series Скачать руководство пользователя страница 136 | Manualshive

Страница: 136 / 236

background image

Chapter 3 Disassembly and Maintenance
3-7. Adjustments

CL-E700 series

3-50

3-7.

Adjustments

3-7-1. Transparent/Reflective Sensor Adjustment

When one of the following parts is replaced with a new one, perform sensor position adjustment
and sensor sensitivity adjustment as shown in the table below.

Parts replaced

Sensor position adjustment

Sensor sensitivity adjustment

SA Main PCB

Through Pos, Reflect Pos

Init Thru Sen, Init Refl Sen

SA TRA Sen PCB
(Transparent sensor)

Through Pos

Init Thru Sen

SA Ref Sensor PCB
(Reflective sensor)

Reflect Pos

Init Thru Sen, Init Refl Sen

(1) Sensor position adjustment (Factory mode)

In Factory mode, perform the following sensor position adjustment. For the adjustment
procedure, refer to the following “Refer to” column.

Submenu

Adjust when the following part is replaced.

Refer to

Through Pos • SA TRA Sen PCB (Transparent sensor)

• SA Main PCB

Reflect Pos

• SA Ref Sensor PCB (Reflective sensor)
• SA Main PCB

2-3-3. Factory/Service

” in Chapter 2

(2) Sensor sensitivity adjustment (Factory mode)

• Since Factory mode menu includes essential items that can affect the

printing accuracy, etc, DO NOT change the factory set values unless
otherwise required.

• Do not turn OFF the power of the printer until you finish the adjustment. If

the power is turned OFF before finishing, you need to repeat the
adjustment from the beginning.

• The value adjusted here is retained until you change it with the same

procedure. Even if you perform initialization by selecting “Test Mode” main
menu, “Factory Default” submenu and then “Yes”, the changed value here
does not return to the initial value set at the factory.

Perform the sensitivity adjustment for each sensor with the following submenu. For the
adjustment procedure, refer to the following “Refer to” column.

Submenu

Adjust when the following part is replaced.

Refer to

Init Thru Sen • SA TRA Sen PCB (Transparent sensor)

• SA Ref Sensor PCB (Reflective sensor)
• SA Main PCB

“3-7-1(2-1) “Init Thru Sen”
sensitivity adjustment”

Init Refl Sen

• SA Ref Sensor PCB (Reflective sensor)
• SA Main PCB

“3-7-1(2-2) Init Refl Sen
sensitivity adjustment”

«
...
134
135
136
137
138
...
»

Содержание CL-E700 Series













































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CL-E700 Series

Webster's Spelling Corrector NC-10

Бренд: Franklin Страницы: 8

PowerScan PM8300

Бренд: Datalogic Страницы: 92

RoadRunners BRR-L

Бренд: Baracoda Страницы: 48

Бренд: Barnes & Noble Страницы: 106

Бренд: Hama Страницы: 16

Бренд: Infinite Peripherals Страницы: 31

Бренд: Honeywell Страницы: 2

Бренд: IDTECH Страницы: 13

Бренд: Datalogic Страницы: 21

00124153 MoveData

Бренд: Hama Страницы: 54

Бренд: ViewSonic Страницы: 73

Бренд: Ocom Страницы: 27

Бренд: Zurich Страницы: 96

Бренд: Sunstech Страницы: 37

Бренд: Sunstech Страницы: 51

Бренд: Diablotek Страницы: 1

Бренд: Atech Flash Technology Страницы: 10

Бренд: Atech Flash Technology Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды