Cisco Wireless Express 526 Скачать руководство пользователя страница 9

Страница: 9 / 44

Configured Country Code

The country for which the controller is
configured. This setting is not changeable in the
startup wizard.

Regulatory Domain

The domain in which the controller is to be
operated. Selection is made using the appropriate
domain checkbox.

AP Manager Interface Name

The name assigned to the access point manager
interface. This setting is not changeable in the
startup wizard.

AP Manager VLAN identifier

The VLAN identifier of the access point
management interface (a valid VLAN identifier
or 0 for an untagged VLAN).

AP Manager IP address

The IP address of the access point manager
Interface.

AP Manager netmask

The Netmask of the access point manager
Interface.

AP Manager Gateway IP address

The IP address of the access point manager
interface.

AP Manager port number

The port number of the access point manager
interface. The default is 1.

AP Manager Primary DHCP Server IP address

The IP address of the access point manager
primary DHCP server interface.

AP Manager Secondary DHCP Server

The IP address of the access point manager
secondary DHCP server interface.

Virtual Interface Name

The name of the controller’s virtual interface.
This setting is not changeable in the startup
wizard. The default is

virtual.

Virtual Interface IP address

The IP address for the virtual interface.

Virtual Interface DNS Host Name

The name of the controller’s virtual interface
DNS host.

WLAN ID

The identification number of the wireless LAN on
which this controller resides. This setting cannot
be changed in the startup wizard. The default is

Profile Name

The profile name of the wireless LAN.

Table 1

Startup Wizard Information (continued)

Wizard Setting

Action

Содержание Wireless Express 526













































Результаты поиска

Содержание Wireless Express 526

Отзывы:

Похожие инструкции для Wireless Express 526

Бренды по названию

Популярные бренды

Cisco Wireless Express 526, Быстрый старт

Результаты поиска

Содержание Wireless Express 526

Отзывы:

Похожие инструкции для Wireless Express 526

Бренды по названию

Популярные бренды