Cisco USC 5030 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 12

Cisco USC 5030 Скачать руководство пользователя страница 6

Description

LED Color

Module slot not detected

Red

Verify Your Small Cell Module Installation

After the USC 5310 module is installed in the USC 5030 chassis and powered up, it takes approximately ten minutes for the module
to initialize, download any necessary software and configuration information, configure the radio frequency (RF) parameters, and
come into service.

Take note of the initialization sequence by noting the color and activity of the LEDs on either side of the module. The module is
ready to use when the LEDs change to solid green.

Figure 3: Cisco USC 5310 Module

Reset button

1

LED

—

the same LED indication displays on both sides of the module

2

Table 2: Cisco USC 5310 LED Indications

Small Cell State / Action

LED Indication

Unknown State or Off

—

Ensure power supply is connected and turned on

Off

Initialization

—

Wait for action to complete

Fast Blinking Green

Temporarily out of service

—

Wait for action to complete

Factory reset

—

Wait for action to complete

6

«
...
4
5
6
7
8
...
»

Содержание USC 5030













Отзывы:

Нет отзывов