manualshive.com logo in svg

Cisco UCS Invicta C3124SA, Руководство по установке, Страница: 24 / 40

Поделиться
Скачать
Cisco UCS Invicta C3124SA Скачать руководство пользователя страница 24

 

2-4

Cisco UCS Invicta C3124SA Appliance Installation Guide

OL-31369-01

Chapter 2      Installing the Cisco UCS Invicta C3124SA Appliance

Preparing for Cisco UCS Invicta C3124SA Appliance Installation

When you are installing a Cisco UCS Invicta C3124SA Appliance, use the following guidelines:

•

Plan your site configuration and prepare the site before installing the Cisco UCS Invicta C3124SA 
Appliance. See the 

Cisco UCS Site Preparation Guide 

for the recommended site planning tasks.

•

Ensure that there is adequate space around the Cisco UCS Invicta C3124SA Appliance to allow for 
servicing the Cisco UCS Invicta C3124SA Appliance and for adequate airflow. The airflow in this 
Cisco UCS Invicta C3124SA Appliance is from front to back.

•

Ensure that the air-conditioning meets the thermal requirements listed in the C3124SA Appliance.

•

Ensure that the cabinet or rack meets the requirements listed in the 

“Rack Requirements” section on 

page 2-4

.

•

Ensure that the site power meets the power requirements listed in the 

Cisco UCS Invicta C3124SA 

Appliance Specifications

. If available, you can use an uninterruptible power supply (UPS) to protect 

against power failures. 

Rack Requirements

This section provides the requirements for the standard open racks.

The rack must be of the following type:

•

A standard 19-in. (48.3-cm) wide, four-post EIA rack, with mounting posts that conform to English 
universal hole spacing, per section 1 of ANSI/EIA-310-D-1992. 

•

The rack post holes can be square 0.38-inch (9.6 mm), round 0.28-inch (7.1 mm), #12-24 UNC, or 
#10-32 UNC when you use the supplied slide rails.

•

The minimum vertical rack space per Cisco UCS Invicta C3124SA Appliance must be two RUs, 
equal to 3.5 in. (88.9 mm). 

Equipment Requirements

The slide rails supplied by Cisco Systems for this Cisco UCS Invicta C3124SA Appliance do not require 
tools for installation if you install them in a rack that has square 0.38-inch (9.6 mm), round 0.28-inch 
(7.1 mm), or #12-24 UNC threaded holes. The inner rails are pre-attached to the sides of the Cisco UCS 
Invicta C3124SA Appliance.

However, if you install the slide rails in a rack that has #10-32 round holes, a bladed screwdriver is 
required to remove the larger square/round mounting pegs from the 

front

 of the slide rails.

Slide Rail Adjustment Range

The slide rails for this Cisco UCS Invicta C3124SA Appliance have an adjustment range of 26 to 36 
inches (660 to 914 mm).

Содержание UCS Invicta C3124SA









































Отзывы:

Нет отзывов