Cisco SCE 8000 10GBE Скачать руководство пользователя страница 221

Страница: 221 / 478

7-29

Cisco SCE 8000 10GBE Software Configuration Guide

OL-30621-02

Chapter 7 Configuring Line Interfaces

Configuring Traffic Rules and Counters

Configuring Traffic Rules

Use the following commands to create and delete traffic rules.

•

How to Create a Traffic Rule for IPv4 Addresses, page 7-29

•

How to Create a Traffic Rule for IPv6 Addresses, page 7-32

•

How to Delete a Traffic Rule, page 7-33

•

How to Delete All Traffic Rules, page 7-33

•

How to Delete All Flow Control Traffic Rules, page 7-34

How to Create a Traffic Rule for IPv4 Addresses

Options

The following options are available:

IP specification:

all|([all-but] (ip-address|ip-range))

•

ip-address

is a single IP address in dotted-decimal notation, such as 10.1.2.3

•

ip-range

is an IP subnet range, in the dotted-decimal notation followed by the number of significant

bits, such as 10.1.2.0/24.

•

Use the

all-but

keyword to exclude the specified IP address or range of IP addresses

protocol:

Any one of the following protocols:

TCP/UDP/ICMP/IGRP/EIGRP/IS-IS/OSPF/all

port specification:

all|([all-but] (port#|port-range)

•

Specify the ports only if the protocol is either TCP or UDP.

•

Specify the port or port range for both the subscriber-side and the network-side.

•

Specify a range of ports using the form MinPort:MaxPort.

•

Use the

all-but

keyword to exclude the specified port or range of ports

id specification:

all|([all-but] tunnel id)

•

tunnel id is an 8-bit Hex value range, in the format '(HEX)

Tunnel-id

' or '(HEX)

MinTunnelId

:(HEX)

MaxTunnelId

', which reflects the lower eight bits of the VLAN tag.

•

Tunnel-ID-based rules can only be used in "

VLAN symmetric classify

" mode (see

“Configuring the

VLAN Environment” section on page 7-16

, and only when

tunnel id

mode is enabled.

Use the

traffic-rule tunnel-id-mode

command.

Note that the VLAN tag itself is a 12-bit value, and therefore aliasing of the lower 8 bits can occur,
depending on the VLAN tags used.

direction:

Any of the following:

upstream/downstream/both

Содержание SCE 8000 10GBE































































































































































































































































































































































































































































































Результаты поиска

Содержание SCE 8000 10GBE

Отзывы:

Бренды по названию

Популярные бренды

Cisco SCE 8000 10GBE, Руководство по настройке программного обеспечения

Результаты поиска

Содержание SCE 8000 10GBE

Отзывы:

Бренды по названию

Популярные бренды